Moderator Emeritus.
The gears are all the same for Ford 8.8s
. The carriers usually come in two different sizes, depending on gear ratio. The spider gears must match your axle spline count as that’s where they attach to the carrier.
Are all Ford 8.8 carriers the same?
Moderator Emeritus.
The gears are all the same for Ford 8.8s
. The carriers usually come in two different sizes, depending on gear ratio. The spider gears must match your axle spline count as that’s where they attach to the carrier.
Is the Ford 8.8 strong?
Ford 8.8 Strength ComparisonThe truth is that the Ford 8.8 is virtually a clone of the Chevy 12-bolt and
therefore almost as strong
. Most rear axles are described by their ring-gear diameters, with larger being better.
What is the difference between 28 spline and 31 spline?
A
28 spline axle will have a recess in the middle
while a 31 spline axle will be solid with just a centering champher (from when it was machined and ground at the factory).
Does a Ford 8.8 have C clips?
There is no need for c-clips eliminators
in the disc brake 8.8’s. The caliper will hold it on if the c-clip breaks and the axle tries to come out.
How much power can a Ford 8.8 handle?
Now strange has desighned a new spool for the 8.8 to handle more power and 35 spline axels, so with the right parts and prep an 8.8 will hold
800-1000 hp
no problem!
Is Ford 8.8 limited slip?
Like other Ford axles, the 8.8-inch came in both 28-spline and 31-spline versions. … Aftermarket lockers are available to adapt the 8.8-inch open rear to
limited
-slip. If you find one with the correct axle width, you can build it to your own specifications easily.
How much power can a stock Ford 9 inch handle?
Sure a 9 inch can handle
400+ horse
in a car.
What vehicles did the Ford 8.8 come in?
First appearing in 1977, the 8.8 is found in almost
all Ford V8 cars from ’86 on, and in V6 Rangers and Explorers
. There are 24 different Fords that offered the 8.8 rear axle. The weakest points of the 8.8 are the 28-spline axles (1.18 inches in diameter).
What Mustangs have 8.8 rear end?
- From ’86-2010 the Ford Mustang 8.8 rear end went into all V8 Mustangs (5.0L, 4.6L & 5.4L) …
- The ’99-01′ & ’03-04′ Mustang SVT Cobras were equipped with an Independent Rear Suspension (IRS) that used the Ford 8.8” differential.
Are 28 or 31 spline axles better?
31 spline axles which are
about 30% stronger than the 28 spline axles
making them a popular aftermarket upgrade for Fox, SN95, and New Edge Mustang owners. … Keep in mind that when you upgrade to the 31 Spline Axles, you will also need a 31 Spline Differential to match up with the new spline requirement!
How much HP can 28 spline axles handle?
The should be good up to
350-400
depending on how you launch the car.. Ive seen them break on stock cars with stickey tires.
Why are more splines better?
Higher spline counts gives the axle more surface to transfer the load of the torque from the differential
. There is also the side advantage that an axle with more splines will also be physically bigger. At least in most modern axles that use similarly sized spline teeth.
Can you run C-clip eliminators on the street?
Can C-Clip Eliminators be used on the street? A.
We do NOT recommend using C-Clip Eliminators for street use
; a C-Clip Eliminator is made for drag race only ( As a safety issue so you do not loose an axle, if it breaks ). C-Clip Eliminators are made for the straight shot down the strip.
How does C-Clip Eliminator work?
WHAT IS A C-CLIP AND WHAT DOES IT DO? On your Mustang’s rear differential, the axle shaft is held in place by a small c-clip. … These eliminators
will completely remove this internal clip and replaced it with an externally pressed on bearing to hold the axle shaft into place
.
