Wheel Speed Sensor Replacement Cost – RepairPal Estimate.
Labor costs are estimated between $62 and $78
while parts are priced between $147 and $176. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.
Can you drive with a bad wheel speed sensor?
That is why in general,
it is unsafe to drive a vehicle with a broken wheel speed sensor
. If the wheel speed sensor becomes damaged or wears out, initially you probably won't notice much difference in the way your car performs if your ABS light comes on unless you are driving on slippery pavement.
What happens when a wheel speed sensor goes bad?
Therefore, a failing speed sensor will have a direct impact on
automatic transmission operation
. One of the most common signs of a bad speed sensor is abnormal automatic transmission operation. If the VSS is faulty, the transmission may exhibit symptoms such as delayed shifts, hard shifts, and limited gear operation.
Is a speed sensor expensive to fix?
The DIY cost for replacing a speed sensor is the cost of the sensor. Depending on the vehicle year, make and model, a speed sensor can cost as little as $7.92 or as much as $100. For most vehicles, the cost for a speed sensor is
between $25 and $45
.
What causes a wheel speed sensor to fail?
What are the common causes of failure? Typically these sensors will fail as a result of
clogging from metallic debris, brake dust or dirt due to exposure to the harsh elements
.
What are the signs of a bad ABS sensor?
- The ABS Light comes on. The most obvious sign of a problem with the ABS system is that the ABS Light will come on. …
- Brakes take longer to stop car. …
- Less stability under icy or wet driving conditions.
How do you tell which ABS wheel sensor is bad?
Loss of stability and traction control: If it detects a bad wheel speed sensor, the ABS computer will usually disable the
stability and traction control systems
, as well. On some vehicles, a bad wheel speed sensor may affect other functions as well, such as hill-start assist and roll stability.
How long does it take to fix a speed sensor?
Most experienced technicians can replace the transmission speed sensor within
2-3 hours
. Depending on the severity of the damage it can take a bit longer.
How do you fix a faulty speed sensor?
- Having found the sensor or sensors to be faulty, remove the connector between the sensor and the vehicle's wiring.
- Using the proper socket, remove the faulty sensor.
- Connect the new sensor to the vehicle's wiring.
- Install the new sensor.
- Lower your car.
- Start the engine.
How do you fix a speed sensor?
- Having found the sensor or sensors to be faulty, remove the connector between the sensor and the vehicle's wiring.
- Using the proper socket, remove the faulty sensor.
- Connect the new sensor to the vehicle's wiring.
- Install the new sensor.
- Lower your car.
- Start the engine.
How long do ABS sensors last?
You can usually expect to get
30,000 to 50,000 miles
out of your ABS speed sensor – more if you don't drive often, or if you live in an area where your car is seldom exposed to dirt, road salt, or other compounds that can cause damage to electronics.
How do you test a wheel speed sensor?
Set a multimeter to measure resistance
(ohms). Place each probe of the multimeter on each pin inside the connector. Connect it to the end of the wire that comes from the sensor. Note the ohm reading on the gauge.
How do ABS wheel sensors work?
Mechanism: The ABS sensor usually consists of a toothed ring and a magnet enclosed within a coil. The contact between the ring and the magnet induces an electric field due to which a signal is generated. This signal is then
transformed into a digital signal
and sent to the ABS controller.
What will a bad ABS sensor do?
Loss of stability and traction control: If it detects a bad wheel speed sensor, the ABS computer will usually
disable the stability and traction control systems
, as well. On some vehicles, a bad wheel speed sensor may affect other functions as well, such as hill-start assist and roll stability.
Can you bypass a ABS sensor?
nope
, no dice. Tried to remove the resistor and put it back on. same thing, light is still on. at this point, resistor does trick the car to see that a sensor is there, but does not give its output that it needs.
What happens if you disconnect ABS sensor?
Removing a wheel speed sensor will disable ABS—and sometimes, stability control
. If your car has a yaw sensor, you can unplug that for results. You can also try simply unplugging the ABS module, though that could adversely affect your car's braking performance.
