How Much Does It Cost To Replace A Half Shaft?

by | Last updated on January 24, 2024

, , , ,

Replacement axle can be bought for

between $60-150.00 each

, and labor is generally between 1.5-3 hours to replace, bringing labor to around $150-350.00.

How much is a half shaft?

Replacement axle shafts can be purchased for

between $96 to $214 each

, while the cost can be between $168 to $799 when both parts and labor are involved. The costs for a double axle joint replacement are, as you might expect, around twice the cost of a single.

How do I know if my half shaft is bad?

  1. Vibration While Driving. This is a tricky one, since there are many things that could cause vibration when you drive. …
  2. A Knocking Sound. Keep an ear out for a knocking or clunking sound, especially a rhythmic one. …
  3. “Clicking” Noises When Turning.

How much does it cost to replace a drive shaft?

You can usually expect to pay

between $320 and $750

for the average cost of the parts, while the cost of the labor is between $150 and $190. If you have a rear wheel or four wheel drive car, then the price of the broken drive shaft repair cost will be much higher.

Can you drive a car with a bad half shaft?

If the boot that seals the CV joint is damaged, the grease will leak out and contamination will set in, eventually causing the joint to wear out and fail. A severely worn out CV joint can even disintegrate while you're driving and make the car undrivable. …

It is not safe to drive with a damaged CV joint

.

What does a drive shaft sound like when bad?

Generally speaking, a bad drive shaft is going to create a kind of

rattling or clunking sound

. You may also hear sounds that are like a high-pitched squeaking or a scraping noise of metal on metal. All of this will originate from underneath your car, rather than in the engine compartment.

What causes a drive shaft to go bad?

Your driveshaft has a U-joint which rotates at a steady pace. If the rotation fails or speeds up too quickly, then it will cause issues with your driveshaft. Perhaps you have a bad U-joint or your bearings have rust on the cap seals.

How long can you drive with a bad drive shaft?

If you allow the driveshaft to die completely, then it will reach the point where the wheels no longer receive any power. While there is no set lifespan of a driveshaft, it typically can

last about 75,000 miles

. Keep in mind depending on the vehicle, and wear and tear you may get much less or much more.

How long does it take to replace drive shaft?

That's very difficult to answer due to the multiple variables involved in removing and replacing hard to access components such as the center driveshaft on a front wheel drive vehicle like your Edge. However, in general, this type of job can often be completed

in one business day

; or less than 8 service hours.

Can a bad drive shaft damage transmission?

For vehicles equipped with driveshafts, they are an important part of the drivetrain and any issues with them can greatly affect the drivability of the vehicle. As they are underneath the vehicle and connected to the transmission, they may be

difficult to access and service

on one's own.

Can I drive with a messed up axle?

If one of

your axles is broken, do not drive the car

. It's not safe. If you notice a bumping, clicking or grinding noise when going into turns, your axle isn't broken yet, but it's only a matter of time. … If your axles are failing, you'll still technically be able to drive your car.

What happens if a CV joint breaks while driving?

If a CV joint begins to fail while driving, your car will start to pull to one side as one wheel loses power. When the joint breaks

completely its corresponding wheel will no longer turn

and although the engine may still run, the car won't move. … If possible, slowly steer your car off the road and then call a tow truck.

What are the signs of a broken axle?

  • Loud clunking noises. …
  • Grease leaking from underneath the vehicle. …
  • Malfunctioning brakes or inability to accelerate. …
  • Vehicle tyre misalignment.

What happens if you don't mark your driveshaft?

If they split the shaft and not re install it correctly,

they will throw the shaft out of balance and cause an uncomfortable vibration

. One piece shaft guys have the slip yoke in the t-case, so they dont have to worry about any of this.

Can you drive without a drive shaft?

You can drive the vehicle indefinitely in this mode with one driveshaft removed.

Never drive

with one driveshaft removed unless the CDL is locked; you can burn up the viscous coupler in vehicles so equiped, but also the vehicle will roll even if the transmission is Park (unless the Emergency brake is engaged).

Should you turn a drive shaft by hand?

So, yes,

you should be able to rotate the driveshaft by turning the wheel

. However, with that said, I personally would get under the car and rotate the DS by hand to visually examine the DS and center mount, Joints, etc. There will be a front and rear Ujoint for each half of the driveshaft with a center bushing.

David Evans
Author
David Evans
David is a seasoned automotive enthusiast. He is a graduate of Mechanical Engineering and has a passion for all things related to cars and vehicles. With his extensive knowledge of cars and other vehicles, David is an authority in the industry.