How Much Travel Should A Slave Cylinder Have?

by | Last updated on January 24, 2024

, , , ,

You are supposed to have

approx 1/4′′

of free play between the throwout bearing and the fingers on the pressure plate. With the pedal to the floor there should be approx 0.050′′ of clearance between the disk and the flywheel or pressure plate (the disk is against one or the other).

How far do clutch fingers travel?

Most clutches call for a maximum gap of

1/16′′ to 1/8′′

. A common mistake is to allow too much gap or too little gap. Do it once, do it right! If you have too little gap, the throw out bearing will constantly be wearing the fingers of the pressure plate.

What are the symptoms of a faulty slave cylinder?

  • Clutch does not work.
  • Clutch pedal sinks to the floor.
  • Clutch pedal feels spongy, soft, or loose.
  • Clutch pedal feels hard.
  • Gears grind while shifting.
  • Gears are hard to shift.
  • Gears will not shift.
  • Clutch fluid low and/or leaking.

How do you adjust a hydraulic slave cylinder?

How much should a pressure plate move?

very little

. 1/4 MM or . 010′′

is fine. Plus; look at the clutch arm play, should be between 3/16′′ to 3/8′′ ‘arc’ play or movement prior to engagement with the heavy duty Clutch kit in place.

Does a release bearing spin all the time?


Its outer surface is always spinning

, whether the clutch is engaged or disengaged. It is self-adjusting, meaning that the spring between the bearing and base puts tension on the bearing, keeping it in contact with the pressure plate.

Should throw out bearing touch pressure plate?

The throw out bearing

must NOT ride on the pressure plate

.

How do you check a clutch air gap?

How do you measure throwout bearing clearance?

Why it is sometimes necessary to adjust a clutch actuation system?


Anything less than the correct amount o free play (or clearance ) will result in clutch slip, because the pressure plate will be unable to exert its full pressure on the friction plate

. Failure to cure this fault will quickly lead to a burned-out friction plate, and possibly a ruined pressure plate.

How do you test a slave cylinder?

  1. Open the hood. Locate the slave cylinder. …
  2. Look around the cylinder for wet spots that indicate it is leaking. If there is fluid coming from the cylinder, it needs to be replaced.
  3. Watch the cylinder as an assistant depresses the clutch pedal. …
  4. Get in the car and start it.

What causes a clutch slave cylinder to go bad?

Once you press the clutch pedal, the master cylinder applies a certain amount of pressure to the clutch slave cylinder, which allows the clutch to release. The clutch slave cylinder can go bad over time

after being used every time you depress the clutch

.

Can a slave cylinder cause clutch to slip?

Master or Slave cylinder leakage.

Most cars these days are hydraulic, so

they rely on fluid pressure from the clutch master cylinder to actuate the clutch slave cylinder

. Age and wear can cause the seals to fail and this can happen either internally or externally.

Where should my clutch grab?

Where should the clutch bite point be?

The bite point is usually

around half way through the clutches working travel (around mid-way from fully pressed to fully released)

. The does however vary a little from car to car. An experienced driver will have little need to use the bite point except for very slow moving traffic and moving off on a hill.

How do I lower my clutch biting point?

To adjust, simply

pull up on the clutch cable and loosen the locknut and the adjuster nut slightly. Next, slowly pull up on the clutch cable again

. You will feel a point where the clutch fork engages. This is where the clutch cable should be adjusted to.

How do you inspect a pressure plate?

Inspect the pressure plate for

warping and hot spots

. This part is often replaced when replacing a worn clutch disc. Inspect the plate’s surface for cracks, scoring, and chatter marks. They leave dark and then light spots around the plate’s surface.

How do you know if your pressure plate is bad?

  1. Difficulty shifting gears.
  2. Clutch may slip or shudder.
  3. Engine will “rev,” but speed will not increase/vehicle will not move.
  4. Abnormal noise from clutch area.

How do you inspect a clutch plate?

Can you replace just the throw out bearing?

The bearing allows the clutch to smoothly operate within the gear box and is essential for proper clutch function. When and if you are changing the clutch, change the throwout bearing also.

Replacing a throwout bearing is simple and can be accomplished by any do-it-yourself mechanic

.

How long will clutch release bearing last?

However, a noisy clutch release bearing can last for

5 years or just 5 minutes

. It depends on your attitude toward responding to a problem in your vehicle. Once you notice a noise from your vehicle’s clutch release bearing, it is ideal for you to see an auto mechanic and get it fixed as soon as possible.

Is a throw out bearing the same as a release bearing?

A throwout bearing is used on vehicles with a manual transmission. It’s part of the mechanism that disengages or releases the clutch when the driver presses down on the clutch pedal. As such,

it’s sometimes also called a release bearing

.

What does the throw out bearing ride on?

The “throw-out bearing” is the heart of clutch operation. When the clutch pedal is depressed, the throw-out bearing moves toward

the flywheel

, pushing in the pressure plate’s release fingers and moving the pressure plate fingers or levers against pressure plate spring force.

How do you remove a throwout bearing from a pressure plate?

David Evans
Author
David Evans
David is a seasoned automotive enthusiast. He is a graduate of Mechanical Engineering and has a passion for all things related to cars and vehicles. With his extensive knowledge of cars and other vehicles, David is an authority in the industry.