Hold stock firmly and
flat on the table
to prevent the stock from turning and drawing your fingers against the blade. Use a push stick when you remove cut pieces from between the fence and saw blade or when your hands are close to the blade.
What is the number 1 safety rule of the band saw?
1.
A two foot perimeter around the saw should be kept clear of people, debris and sawdust that impair traction or footing to avoid slips and falls
. 2. Safety glasses with side shields or a face shield must be worn.
Where should you stand when cutting with a bandsaw?
Keep upper and lower doors closed and all guards in place
. Cutting cylindrical or irregular stock on the band saw may be done only with a special jig, such as a V-block (special setup). Never stand or allow others to stand to the right of the band saw when it is running.
When cutting on the bandsaw you should?
When operating a band saw, you
should stand facing the blade and slightly to the left
. Move the stock into the blade as slowly as possible to avoid burning the wood. In general, you should make long cuts before short cuts.
How do you operate a band saw correctly?
- Read the owner’s manual carefully.
- Make sure you understand the instructions before attempting to use any tool or machine.
- Learn the applications and limitations before use.
- Securely anchor the band saw to the floor (or a workbench of appropriate height) to reduce vibration.
When using the band saw why is it important not to back out of a cut?
6. Make curved cuts gradually and use relief cuts for tight radius curves. Never back out of curved cuts while
machine is still running
as this will result in the blade coming off.
What shaped stock should not be cut on a table saw?
Round stock
should not be ripped on a table saw. 18. When making bevel cuts, always keep hands and stock to the right of the saw blade.
When backing off from a long cut you should?
If it becomes necessary to back out of a long cut, you should:
Turn off the motor. Bring the blade to a complete stop and then back the stock out carefully
. Force the wood into the blade to get a good cut.
What should you adjust above the work before beginning to cut?
Ensure that
the blade is running at full speed
before starting a cut. Cut on the waste side of your line, leaving the pattern line on the work. Keep your hands beside or behind the blade. Never in front.
What does resaw mean on a bandsaw?
Bandsaw Resawing from the beginning: resawing is
cutting a sawn plank of wood into thinner planks on a bandsaw
. Thus the cut runs through the plank’s width, which distinguishes bandsaw resawing from ordinary bandsaw rip cuts where the blade runs through the stock’s thickness.
What should you not do with a band saw?
- Do not use excessive force when pushing the wood past the blade.
- Do not back the stock away from the blade while the saw is in motion if the work piece binds or pinches on the blade.
How thick can a band saw cut?
Band saws are the undisputed champ when it comes to cutting curves and slicing through thick material. Many small band saws can slice though lumber a full four inches thick, and bigger saws handle
six-inch cuts
.
What is the difference between a band saw and a jigsaw?
The jigsaw is
suitable for rough cutting and general cutting purposes
. … The bandsaw is used for large-scale accurate cutting. It is mostly used to cut larger pieces of lumber and wood. The jigsaw can make smaller cuts but can’t be used for making larger cuts in line.
Does the splitter keeps the saw kerf open?
As its name implies, the
splitter keeps the kerf open after the blade makes the cut
, preventing pinching that can burn a cut. … Use a straight piece of wood to check that the splitter is directly behind the blade so it doesn’t interfere with the cut.
When starting the band saw the operator should stand?
A student assisting the operator should
stand to the right side of the blade
. The teeth of the bandsaw blade should point up at the point of operation. When cutting tight curves with the bandsaw, you should first make relief cuts. The bandsaw must be at a dead stop before any adjustments are made.
When must the operator use a push stick on the table saw?
For
materials shorter than 12 inches or narrower than 6 inches
always use a push stick or push block to push material between the fence and the saw blade.
