This also means that if you are replacing your stock Fox Shock (like a DPX2) Marzocchi Bomber CR,
you can totally just reuse your old hardware as long as it’s not damaged
!
Can you reuse shock mounting hardware?
This also means that if you are replacing your stock Fox Shock (like a DPX2) Marzocchi Bomber CR,
you can totally just reuse your old hardware as long as it’s not damaged
!
How do you remove shock mount bushings?
How do I remove shock mount from shock?
How do you remove rear shock mounting hardware?
How do you remove rear shock absorbers?
Remove the shock absorber top mounting nut/bolt(s). Loosen and remove the mounting bolt(s) at the bottom of the shock absorber. Remove the shock absorber from the wheel arch. Fitting is a reverse of removal, making sure you tighten the mounting nut/bolt(s) to the specified torque rating.
What shock hardware do I need?
One way to measure the width of the shock hardware is to
measure the distance between the shock mounting tabs on the frame of the bike
. To get the same measurement, you may also measure the width across the shock eyelet. Lastly, to find the shock bolt diameter, measure the inner diameter of the hardware eyelet.
Are Fox and rockshox mounting hardware the same?
Fox hardware uses the poly IGUS bushing, but much older Fox hardware uses a steel bushing.
RockShox hardware is about the same, but just uses one spacer with an integrated o-ring on each side, and a metal DU bushing
.
Are Fox and rockshox interchangeable?
Thankfully,
Rockshox and Fox mounting hardware are cross compatible
, but there’s a few differences that need to be noted before you simply purchase Fox hardware for a Rockshox shock.
How do you install rear shock bushings?
How do you remove strut rod bushings?
How do you install shock bar pins?
Do you need to replace rear shock mounts?
A simple rule of thumb is that
if the struts or coil springs are being replaced because of age or wear, then also replace the mounts
. A worn or damaged mount can cause a variety of symptoms so they should be inspected by a qualified technician.
How do you loosen a shocked Bolt?
How do you remove shock absorbers?
How do you install shock hardware?
How do you install rear shocks on a mountain bike?
Can I replace rear shocks myself?
If you need to replace your car’s shock absorbers but don’t want to pay an expensive mechanic’s fee,
you can do so on your own with a little effort
. Shocks are essential to a car’s performance, giving it a smooth and even ride.
Can you change shocks without a jack?
You can definitely do it
.
How long does it take to change rear shocks?
In most cases, it shouldn’t take more than
a couple of hours
to get back on the road again. If you’re interested in replacing shocks and struts on your vehicle, you’ve come to the right place. In this article, we’re discussing the difference between the two and how to replace them so you can save some money.
How do you measure shock hardware on a mountain bike?
- Measure the eye to eye length.
- Attach a shock pump and slowly remove all the air from the shock.
- Compress the shock fully and measure the eye to eye length again.
- Subtract this measurement from the initial eye to eye length to find the usable stroke. (ie. 185 – 132.5 = 52.5)
Do rear shocks have mounts?
The mounts are what attach the rear struts to the body of the car
. One end of the each rear strut mount bolts directly onto the car’s body, and the other end is attached to the strut. That way the strut stays in place. The rear strut mounts do more than just attach the struts to the car’s body.
Are all MTB shock mounts the same?
For My Rear Shock?
All frames use different sizes of mounting hardware
. This isn’t frame size specific, just specific to the year, make and model.
How do you remove shock hardware?
Use an easy-out mounted in a vice to remove the old reducers. Gently press down on the shock while turning anti-clockwise to engage the easy-out helix. Keep turning anti-clockwise and pull the shock upwards, the reducer should then come out without damaging the shock eyelet. Repeat for other side.
What is a rear shock?
Rear shocks
consist of two telescopic tubes which slide into each other, a spring of some type and an eye at either end through which the whole mechanism is affixed to the frame
. A small bushing (a type of simple bearing) in each eye enables the shock to pivot smoothly when the suspension is active.