Put your finger into the drain outlet and feel the impellers if the pump freely turns
. One or more of them may be broken. If so, you'll be able to feel them while you're turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.
How do I fix the pump on my GE washer?
Is it worth fixing a water pump on a washing machine?
A leaking water line or washer that doesn't drain may seem to be on its way out, but the part responsible for these processes, the water pump, is actually quite easy to fix or even replace on your own.
Replacing a washer pump is not only a relatively easy repair, but also one that saves a lot of money
.
How do you unclog a GE washing machine pump?
Where is pump filter on GE front load washer?
How do you test a washing machine pump?
Why won't my GE washer drain and spin?
Doesn't Spin
When a load is properly balanced but still won't spin, there may be an issue that prevents the water from draining from the machine.
Make sure the drain hose is properly connected and that there are no kinks or pinched areas
. Your washer may not drain and enter the spin cycle if the pump filter is clogged.
Where is the drain pump on GE top load washer?
The drain pump is situated
at the bottom of your washer
. To remove the faulty pump, first disconnect the wire harness from the pump motor. Next, use a 3/8′′ socket and ratchet to take out the bolts holding the pump in place. After the bolts are out, remove the two hoses attached to the drain pump.
Why is my GE washer not draining or spinning?
GE's washer
may have a clog in the hose, filter, or pump
, which can cause the washing machine not to drain. Troubleshooting steps: To fix this, turn off the washer and unplug it from the power outlet. Then, remove any kinks in the hose and double-check that it's connected to your GE washer properly.
How much does it cost to replace a water pump on a washing machine?
The price of a new washing machine pump is
$25 to $40
on its own, not including labor. When hiring a professional, repair prices range from $200 to $450.
How much does it cost to replace a water pump on a washer?
On average, expect to spend
$300 to $400
for a pump replacement job. Washing machine pump repairs are usually required when you note active leaks or a tub that doesn't drain. If the tub does not move, but the agitator does, this indicates the pump is starting to experience issues.
Is it expensive to replace a pump on a washing machine?
Another common problem with a washing machine is a faulty pump which can cause many issues.
On average, the average washing machine pump repair cost is around £98
. Other washing machine repairs costs include circuit board repair, transmission repair, timer repair and belt repair.
How do I clean the filter on my GE top load washer?
If the filter is clogged,
heat up a pan with equal parts water and vinegar to 160 degrees Fahrenheit and soak it in the pan for 15 minutes. Brush both sides with a stiff brush under running water
. These pans can also be soaked overnight in vinegar and water.
Where is the drain pump located on a washing machine?
The purpose of the drain pump is to pump the water from the wash, through the drain hose, to then be drained away. The drain pump is located at
the bottom of your washing machine
, but can be easily accessed in order to replace it if need be.
Do GE front load washers have a filter?
Due to the design of a front-load washer, it is sometimes possible for small articles to pass to the pump.
The washer has a filter to capture lost items so they are not dumped down the drain
.
Is there a filter in my GE washing machine?
There are 2 crescent-shaped Fine Mesh plastic lint filters in the bottom of the wash basket under the agitator
. Water flows through the filters from the bottom of the tub, accumulating any lint on the bottom of the filter screens.
Do all front load washers have a filter?
Clear Drain Pump Filter:
Every front-loading machine will have a drain pump filter
, typically located near the bottom of the machine. Consult manufacturer instructions for the location, as well as how to access the filter door. Clear this filter after every few washings.
How do you fix a water pump?
What causes a washing machine pump to break?
A pump can fail in two ways: mechanically and electrically. A mechanical failure can be caused by
a foreign object caught in the pump, or direct damage to a pump component, such as the impeller
. Inspecting the pump can often reveal a mechanical failure. An electrical failure can be diagnosed by using a multimeter.
How do you test a front load washer drain pump?
How do you fix a GE front load washer that won't spin?
- Remove any kinks in the drain hose. …
- Inspect the household drain. …
- Check the drain and make sure there is an air gap between the hose and drain. …
- Clean the pump filter. …
- Rearrange the clothing in the load. …
- Allow the washer to cool down for two hours.
How do you force a GE washer to drain?
- TURN OFF THE POWER. Unplug the washing machine from the power outlet.
- REMOVE LAUNDRY. Take out any clothing that's in the washer tub.
- EMPTY THE TUB. Use a bucket to scoop the water out of the washer tub. …
- MOVE WASHER AWAY FROM THE WALL. …
- DISCONNECT DRAIN HOSE. …
- PINPOINT THE ISSUE.
Why is my GE front load washer not draining?
Why is my GE front load washer not draining water?
The drain hose may be kinked or blocked by an obstruction
. Gently straighten any kinks or disconnect the hose to locate and remove blockages.
Do top load washers have drain pump filters?
Top-load washers and standard top-load washers
usually require removing the outer housing to access the water pump filter from the back of the machine
. You may find lots of lint, coins, buttons, or even a sock that is causing a slow drain and leaving lint on your clothes.
