The 727 is a
relatively simple
piece when compared to other automatic transmissions, and its strength is a function of that simplicity. We’ve put stock TorqueFlite transmissions behind big-blocks pushing upwards of 600 hp and found they not only survive, but perform quite well.
Who makes the 727 transmission?
The
Chrysler
A-727 transmission, also known as the TorqueFlite 8 units is a three-speed transmission that was launched around 1956.
What is the difference between a 727 and 904 transmission?
Re: What is the difference between the 727 and the 904 transmission? The 727 was the only available automatic transmission for big block cars. You could get a 727 for a small block, which where mostly for 340’s and 360’s or you could get a 904 which was primarily for the
318
.
How much does it cost to rebuild a 727 transmission?
around hear they usally get
between $300.00-$500.00
for a rebuild if you take the trans to them, coarse for that kind of money you can bet they use the cheap kits.
How many gears are in a 727 transmission?
Gearing for the 727 is
2.54:1 for 1st gear
, 1.54:1 for second, 1:1 for third and 2.21:1 for reverse. The weight of the transmission is a hefty 161 lbs.
How much horsepower can a 904 transmission handle?
As everyone has said, a properly built 904 will take that
360
without an issue.
How can you tell a 727?
An A-727 can also be identified as being a 1978 and newer
lockup units just by examining the transmission’s input shaft
. It was built with a lockup if the shaft is smooth at its last half inch, on the contrary, if it is splined to the end of the input shaft, then it is a non-lockup transmission.
Is it hard to rebuild a 904 transmission?
Rebuilding an automatic transmission is
generally regarded as a difficult undertaking
because the repair shop must be familiar with your specific type of transmission. Automatic transmissions vary widely from one vehicle to the next and each requires totally different parts and tools to rebuild.
How much horsepower can a 727 handle?
The 727 is a relatively simple piece when compared to other automatic transmissions, and its strength is a function of that simplicity. We’ve put stock TorqueFlite transmissions behind big-blocks pushing upwards of
600 hp
and found they not only survive, but perform quite well.
Does 727 have overdrive?
Convert Your 727 To A
Six-Speed Overdrive
With Gear Vendors’ Tailshaft-Mounted Overdrive Unit. … With the overdrives came the additional benefits of reduced engine wear, noise, and effortless high-speed cruising. Crank any new vehicle up to 90 mph, and it’s a Sunday drive.
What vehicles have 46RE transmission?
- Dodge Ram pickup and vans 150/250/350 V8 and diesel engines (DGT)
- Dodge Ramcharger SUV 1988-1993 5.2L & 5.9L V8.
- Jeep Grand Cherokee 1993 5.2L, 1998 5.9L.
- 1995 Dodge Dakota 5.2L Magnum V8.
- 1996 Dodge Dakota V8.
- 1998–2003 Dodge Dakota R/T.
- 1998-2003 Dodge Durango 5.9L V8 (4WD or 2WD)
What is a 904 transmission?
The aluminum 904 was first introduced by the Chrysler Corporation in 1960, and is a design that evolved from the Chrysler PowerFlite, which was a
two speed automatic
, and then the cast-iron three-speed TorqueFlite which was durable but heavy.
How much does a 904 transmission weight?
I bet
90 lbs
is a close estimate.
What kind of fluid goes in a 727 transmission?
Ron is also a believer in synthetic automatic transmission fluid and says the old standard Type-F is outmoded today because it breaks down and foams more readily. A less expensive alternate is
Chrysler ATF+4 fluid
, which is a semi-synthetic blend.
How long is a 904 transmission?
| Style A C | Small Block 30 3/4 in. 24 5/16 in . |
|---|
How much fluid does a 727 transmission hold?
8 to 9-1/2 qts
.
