In my opinion, you should purchase the
planer
first. You’ll be able to accomplish more with it on its own than you can with a jointer. The jointer excels at making one flat face and one square/flat edge and that’s about it.
Can a planer work as a jointer?
A
planer can be used
as a jointer by following a few woodworking tricks. … If your workshop doesn’t have a jointer to square up an edge or your wood piece is too large to fit through, you can use your planer to flatten both pieces of wood.
What is the difference between a planer and jointer?
A jointer creates a flat surface on wood, and yes, it can be used to correct bow and warp on one side of a board at a time. “A planer is a thicknesser. It takes a thick board and makes it thinner. … At the same time, the planer will also make the rough
side both
smooth, and parallel to the other side.
Can you use a planer without a jointer?
-wide jointer that can keep up with your planer, Asa Christiana gives you a few great ways to get flat, straight boards without owning a wide jointer. One of the first milling tools most people buy is a thickness planer. … That means you don’t just need a jointer; you need one as wide as the boards you’ll commonly use.
What does a jointer and planer do?
A
jointer flattens a face or straightens and squares an edge, and a planer thicknesses wood
. Whether you need one, the other, or both can easily be answered by knowing how they work, what they do, and how much wood surface preparation you pay your lumberyard to do for you.
Do you really need a jointer?
Simply
purchase your lumber already milled in S3S or S4S form
(surfaced on three sides or surfaced on 4 sides). If you’re at a point in your woodworking where you’re starting to use rough sawn lumber, say from a lumber mill or your local sawyer, then a jointer is absolutely essential to your shop workflow.
Are planers worth it?
If you really want to get into woodworking, a
thickness planer is worth the cost
. Once you have it, you’ll never regret the expenditure, because you’ll be in control of your stock thickness like never before. … A fellow member might be willing to thickness-plane some stock for you for little or nothing.
Will a planer fix warped boards?
In order to flatten a warped, twisted, or cupped board, a common approach is
to first use a jointer to create one perfectly flat face
. Then you run the board through a thickness planer with the flat face downward, and the planer makes the top face parallel to the bottom.
What if I dont have a jointer?
If you don’t have one, and one isn’t available to you, you can
make a router sled and use that to flatten both faces of your board
, then a different technique to edge joint them. Last but not least, this will hold true for all the techniques mentioned, you can always use hand tools!
How do you flatten a board without a jointer or planer?
- Use a table saw. If you’ve got a large board to plane, a table saw might be a good option. …
- Use a router. You can use a router to substitute for a wood planer in a similar way to a table saw. …
- Use a jack plane. …
- Use a wide-belt or drum sander. …
- Get out the sandpaper. …
- Take it to a cabinet maker.
How much should a jointer take off?
Again, the maximum cut will depend on the width and density of the workpiece, but I generally don’
t remove more than about 1⁄8′′ at a time
. For pieces that aren’t much longer than your infeed table, hook your heeled pushblock onto the trailing end of the board.
Why is it called a jointer?
The jointer derives its name
from its primary function of producing flat edges on boards prior to joining them edge-to-edge to produce wider boards
. The use of this term probably arises from the name of a type of hand plane, the jointer plane, which is also used primarily for this purpose.
What does a thickness planer do?
A thickness planer is
a woodworking machine to trim boards to a consistent thickness throughout their length and flat on both surfaces
. It is different from a surface planer, or jointer, where the cutter head is set into the bed surface.
