Famowood Glaze Coat is a pour-on epoxy coating. This ultra-clear, high-gloss finishing epoxy is ideal for home improvement and craft projects.
Just one coat equals 60 coats of varnish
. Glaze Coat is great for coating tables, bar tops, preserving pictures and photographs or imbedding items such as coins or rocks.
How long do you mix glaze coat?
You have
about 15-20 minutes working time
after Glaze Coat is completely mixed before product begins to harden. Glaze Coat is self-leveling. Spread the mixture over the area with a plastic spreader, plastic squeegee, notched trowel or brush.
How do you mix glaze coat epoxy?
Pour equal parts each of resin and hardener into separate clean, unwaxed disposable paper or plastic cups or tubs. Mix MUST be a
one-to-one ratio (by volume)
, meaning equal parts resin and hardener. If possible, use a calibrated container.
How long does it take Famowood glaze coat to cure?
Allow fresh pours to cure in a warm room (at least 70 °F). Glaze Coat will fully cure in
72 hours
. An additional 1 – 2 coats may be applied after 4 – 5 hours. A third coat can be poured after 24 hours but no longer than 48 hours.
How long does glaze coat take to dry?
A full cure takes
24 to 72 hours
, depending on the surrounding environment. With lower temperatures and higher humidity, cure time increases; with higher temperatures, cure time decreases. To speed drying time, apply heat using a handheld dryer set on low. Hold dryer at least 6 inches from the surface.
Do you sand between glaze coats?
Glaze Coat can only be cleaned while it is still in a liquid state. After it has cured, paint remover,
heat gun or sanding is required
.
Why is it necessary to shake stir the glaze before applying it?
However, as materials in some glazes tend to settle after standing, it is important to
shake or agitate the container vigorously
, then stir, before use. If after shaking and stirring the glaze it is still too thick to load a glaze brush easily then it may be necessary to add a little water.
Does glaze need a top coat?
ANSWER:
Yes
! GF recommends sealing Glaze Effects with High Performance Top Coat. Even though General Finishes Milk Paint does not require a top coat for light to medium wear, once Glaze Effects is added GF recommends sealing the piece with High Performance.
Does tacky epoxy ever cure?
You cannot leave the sticky resin,
as it will not harden after time, it will remain sticky
. You will have to either throw your item away or fix the problem. In order to avoid the problem all together make sure to do the following: You must measure out your resin and hardener precisely.
Do I need to sand between coats of epoxy?
Sanding will not only get out the imperfection but will also
serve to provide some tooth between the first and second layers
. It will look very scuffed in the short term but do not worry, once you pour the second coat over top, all of those sanding marks will disappear.
How deep can you pour Famowood glaze coat?
Glaze Coat CRAFT is self-leveling. However, if necessary, spread the mixture over the area with a toothpick or small tool. Do not persist in re-spreading the mixture as it sets up, otherwise it will not self-level during the curing action. Do
not pour more than 1/8” thick
in an application.
Can you put polyurethane over Famowood glaze coat?
To coat over polyurethane or acrylic finishes,
lightly sand the surface and wipe with acetone or alcohol
before using Glaze Coat. To catch drips, cover surrounding area with waxed paper or drop cloth. Allow drips to flow freely off the sides by elevating area to be coated.
Is glaze coat waterproof?
Glaze Coat® is a pour-on, high-gloss finishing epoxy that is perfect for home improvement, craft and woodworking projects. The ultra-clear, two-part Glaze Coat features an easy 1:1 ratio mix that yields a durable,
waterproof and heat resistant coating
equal to about 60 coats of varnish at 1/16′′ thick. .
What do you seal wood with before epoxy?
Before applying epoxy,
sand smooth non-porous surfaces
—thoroughly abrade the surface. 80-grit aluminum oxide paper will provide a good texture for the epoxy to “key” into.
How many coats glaze coat?
before using FAMOWOOD® Glaze Coat®
Follow measuring and mixing instructions carefully. Product will not cure properly and will be soft or sticky if directions are not followed precisely. Two mixing steps are required. Most applications require
two coats
for a deep, beautiful finish.
