| Fastener Type Torque Spec | Harmonic Damper Bolt 60 ft.-lbs. | Flywheel/Flexplate Bolts 65 ft.-lbs. | Pressure Plate Bolts 35 ft.-lbs. | Bellhousing Bolts 25 ft.-lbs. |
|---|
How do you torque a flywheel?
Place a pry bar, pipe, or some other piece of metal between the bolt head and the ground.
Turn the flywheel in the direction of engine rotation until it makes contact with your prop
, and torque away!
How tight do flywheel bolts need to be?
Tighten all bolts evenly, 1⁄4 turn at a time in a crisscross pattern until flywheel is completely drawn-up to the crankshaft. Torque all bolts in 3 steps: First to 25 ft/lbs. then 60 ft/lbs. Final torque to:
78 – 80 ft/lbs.
What are torque specs?
Torque is
measured as a unit of force acting on a rotating lever of some set length
. … Remembering that torque is the turning effort or force applied to the fastener to preload it, or place it in tension, and is normally expressed in inch-pounds (in.lb) or foot-pounds (ft.lb).
What are the torque specs for clutch?
A small amount of threadlocking compound is recommended on all clutch fasteners. DO NOT use a washer with this pressure plate bolt. Tighten all bolts evenly, 1⁄4 turn at a time in a crisscross pattern until pressure plate is completely drawn-up to the flywheel. Final torque to:
25 – 28 ft/lbs.
Do you need to torque flywheel bolts?
Tighten all bolts evenly, 1⁄4 turn at a time in a crisscross pattern until flywheel is completely drawn-up to the crankshaft. Torque all bolts in 3 steps:
First to 35 ft/lbs. then 80 ft/lbs.
Can you over tighten flywheel bolts?
OFF! Not only is it possible to overtorque them,
it is possible to break them with
that much torque. More likely will be warping the flywheel when you apply 350 lb/ft of torque to 1 bolt while there is no torque on the others.
How do you keep the flywheel from turning?
Put lubricant
all over the balls
Use a bar of some sort and position it on the teeth of the flywheel and the frame. Or, hit your rachet with a hammer fast and hard. It’s kinda like a poor man’s impact gun but it works. You use the flywheels own weight as inertia to keep it from spinning.
What causes a loose flywheel?
It’s happens more often in higher gears and when you push down the accelerator pedal more than just a little bit. This is often a direct result of
a clutch that’s worn out
. Allowing the clutch to slip will eventually cause the flywheel to wear out as well.
What is the torque specs for a axle nut?
For a double nut or jam nut system, bend the lock tab or install the set screw after the outer nut is torqued to 200 ft-lbs. For one-piece spindle nut systems, torque the nut to
a minimum of 300 ft-lbs.
What happens if you dont torque to spec?
Insufficient torque
Engines that
are running, tend to vibrate
. … In the case of insufficient torque, it’s the stud or the bolt itself that suffers all the impact, causing it to shear. Alternatively, the engine’s vibrations can cause the bolt or nut to come undone, displacing the tensioner.
What are the torque specs for spark plugs?
| Thread Size Recommended Torque Recommended Tightening Angle | New Plug | M14 20-30N・m About 2/3 turn | M18 30-40N・m About 1/4 turn | M14 Taper seat 10-20N・m About 1/16 turn |
|---|
What is a torque converter bolted to?
The housing of the torque converter is bolted to
the flywheel of the engine
, so it turns at whatever speed the engine is running at. The fins that make up the pump of the torque converter are attached to the housing, so they also turn at the same speed as the engine.
