Chain saw bar and chain oil isn't rated by SAE like traditional automobile motor oil. … If your manufacturer's bar and chain oil is unavailable, you can use
SAE 30 weight motor oil
to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can you use regular oil for bar and chain oil?
Chain saw bar and chain oil isn't rated by SAE like traditional automobile motor oil. … If your manufacturer's bar and chain oil is unavailable, you can use
SAE 30 weight motor oil
to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
What can I use if I don't have bar and chain oil?
- Motor Oil. Motor oil is the most readily available alternative lube available. …
- Vegetable Oil. Vegetable oil is also a quite affordable bar and chain oil alternative. …
- Canola Oil. Canola oil shouldn't be confused with vegetable oil. …
- Drained Hydraulic Fluids.
Can you use 10w30 for bar and chain oil?
Can I Use 10w30 for Chainsaw Bar Oil?
Yes
, though it is not ideal for use in the winter. A 10w30 oil is multi-weight, meaning it will perform well in cold and heat. Yet 10w30 weight motor oil will be very tacky and viscous once the chainsaw heats up and starts to run.
What kind of oil can you use for chainsaw?
Petroleum-based bar oil
has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner's manual suggests alternatives.
What's the difference between chainsaw oil and motor oil?
Bar and chain oil is stickier than regular motor oil
, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry's tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
What is SAE 30 oil?
SAE30 is a
straight 30 weight oil used on your lawn mower and other 4 cycle outdoor equipment
. … SAE30 weight oil is rated only at the full operating temp of the engine. This means it is much higher than 30 when cold. Sometimes so thick that it cannot flow if it is cold enough out. The W means winter.
Can I use gear oil as chain lube?
Of course you can use gear oil on your chain. It's an extremely
good high pressure viscous lubricant
, and unlike engine oils, it does not contain detergent additives which make engine oil less resistant to water washout.
What happens if you run a chainsaw without bar oil?
No bar oil equals increased friction and heat
. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
Can I use vegetable oil in a chainsaw?
Effective – Vegetable oils have natural
properties
including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
What weight is chain and bar oil?
Once temperatures rise, switch back to your standard bar and chain oil, which may be anywhere
between 20 and 50 weight (30 weight is standard)
. Using winter oil during summer might leave a lot more oil on the ground because the thinner oil won't adhere as well to the bar and chain.
Can you use motor oil for 2 stroke mix?
Use a
40:1 two-cycle oil
mix ratio. One gallon of gasoline combined with 3.2 oz of two-cycle engine oil. Unsure of the age of your equipment?
Can I use motor oil in an electric chainsaw?
Electric chain saws can use
only bar and chain lubrication oil
in their systems. These oils are specifically designed for this kind of lubrication. They are also manufactured to be safe for the environment. Any other kinds, like reclaimed motor or vegetable oil, can damage the oiling system.
Can I use olive oil on my chainsaw?
Use chain saws weekly at the farm and we use motor oil as chain lube often, no problems. Olive oil would just be more expensive. Olive oil tends to get a bit gummy when used as a lubricant, but if you clean it once in a while with a decent solvent it should be fine.
How much bar oil should a chainsaw use?
When to Oil
Gas chainsaws use
about one tank of bar and chain oil for every tank of fuel
, so fill the reservoir every time you fill the tank.
What is chain saw oil?
Chainsaw Oil is specifically
developed for the lubrication of chain and guide bars of modern chain saws
. Selected mineral base oils are combined with special additives to provide good protection against wear, rust and corrosion.
