What Causes An Ice Maker To Stop Making Ice?

If your ice maker isn’t producing ice at all or is producing crescents or cubes that are smaller than usual, it’s typically indicative of

a clog somewhere along the supply line

. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.

How do you troubleshoot an ice maker?

1. Check the shutoff arm.
2. Check the supply valve.
3. Inspect the water supply line.
4. Test the shutoff switch.
5. Check the freezer temperature.
6. Inspect the ejector gear.
7. Test the ejector motor.
8. Test the ice mold heater.

How do I reset my ice maker?

Unplug the refrigerator for 30 seconds; then plug it back in. Within 15 seconds of restoring power,

press the feeler arm three times in succession

. This should force the ice maker to run water into the reservoir and begin the cycle of ice production.

How do I unclog my ice maker?

Apply heat with a hairdryer to

the ice maker fill tube, which is usually a white, rubber-like hose. Hold the nozzle of the hairdryer at the front of the ice maker so that the heat will blast into the fill line. Set the hairdryer to its lowest heat setting to avoid melting the plastic lines and parts of the ice maker.

How do I force my ice maker to cycle?

1. Open the freezer door to remove the ice bin from below the ice maker.
2. Empty the ice from the bin. …
3. Press the ice maker toggle switch to the “On” setting if it is not already activated.
4. Pop off the front cover of the ice maker with the tip of a flat-blade screwdriver.

How do I know if my ice maker is working?

1. If the icemaker mold is empty, you can manually pour about 4 ounces of water in the icemaker mold.
2. Wait about 2 hours.
3. If the icemaker has dropped ice cubes out from the mold, you know the icemaker itself is working.

Why won’t my ice maker fill with water?

Water may not be reaching the ice maker due to a frozen line,

missing filter

, or a closed supply valve. … When there is no filter, or it is clogged, the ice maker does not get water. Make sure that the filter is in place, and if it has not been changed in more than six months, replace it with a new one.

Where is the reset button on my Whirlpool ice maker?

1. At the bottom of the ice maker.
2. Above the ice tray.
3. Underneath the ice tray.

Can water filter cause ice maker not to work?

A clogged or incorrectly installed water filter can reduce the water flow to the ice maker and dispenser and could cause one or more of the following:

Odd tasting ice or water

. Ice maker not producing any ice. Measure fill not working correctly.

How do I force my Whirlpool ice maker to cycle?

Look at the

center of the Whirlpool icemaker to find the rotating arm that pushes the ice cubes out

. Grab the plastic teeth on the arm, and gently pull them in a clockwise direction. You will hear a slight winding sound. The icemaker should start into its cycle.

Why is my Frigidaire ice maker not making ice?

Sometimes, a Frigidaire refrigerator ice maker not making ice is

due to frozen water clogging the supply line

. Frozen water will restrict or completely block water going to your fridge. To check the supply line yourself, start by moving the refrigerator to look behind it for the supply line.

Why did my Whirlpool ice maker stop making ice?

A clogged water filter, kinked water line hose, or defective water inlet valve can restrict the water flowing to an ice maker

. When this happens, ice production will be limited or completely stop.

Should ice maker be up or down?

As ice is made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.

Do not force

the wire shutoff arm up or down.