What Does The Airbag Control Module Do?

by | Last updated on January 24, 2024

, , , ,

An SRS airbag module, also known as the airbag electronic crash unit,

controls the airbag’s deployment, stores crash data and exchanges information with the car’s engine

.

How much does it cost to replace an airbag module?

On average, expect around $1,000 to $1,500 per airbag that needs to be replaced. That doesn’t take into consideration other parts that need to be changed; just the airbags themselves. Airbag module replacement will run

another $600 and up

.

How do I know if my airbag module is bad?

Symptoms of a failing airbag sensor

You can easily tell if the sensor is functioning if the

airbag warning light on the dashboard is illuminating every time

you start the vehicle. But, if the airbag warning light stays illuminated after starting the vehicle, this is an indication of an airbag sensor problem.

Can you drive without airbag module?

While a vehicle can still run without an airbag module, it is strongly recommended that

drivers do not operate the vehicle without it being installed

—unless an emergency situation arises and there is no other option. … Without airbags deploying, a driver and any passengers can face severe injury or even death.

How does an airbag module work?

Airbag control modules

store hard and soft codes caused by accidents

. Even after small accidents, fault codes will be stored in the module which will turn on the airbag light. We reset and clear all crash codes inside the computer module which will turn off the airbag light.

Can you reset airbag module?


All airbag control modules can be reset and reprogrammed

, with the exception of flood, fire or hardware damage.

Where is my airbag module located?

The location of the airbag module differs from vehicle to vehicle, depending on the make and model of it. In some vehicles, it is located in the center console, kick panel, under the radio, or behind the steering wheel. Generally, though, it can be found

underneath the driver’s seat or front passenger’s seat

.

How long does it take to replace airbag control module?

The repair work is expected to take

about 2 hours

to complete, depending on dealer schedules. While repair times can vary from 1 to 2 hours, wait times might be longer depending on dealer schedules.

Do you have to replace airbag module?

If your airbags have deployed during an accident, your airbags will need to be replaced, and your airbag control

module will need to be replaced or reprogrammed

. … It is recommended that a licensed technician replace damaged or deployed airbags to ensure proper care for safety on the road.

Is your car totaled if airbags deploy?


No, airbags deploying does not automatically make a car a total loss

. If a vehicle’s airbags deploy and the cost of replacing them is more than the total loss threshold for your state, it would be declared a total loss.

Does insurance cover air bags?

In most cases,

your vehicle insurance should include your airbag replacement

. However, because this repair is so expensive, it’s common for insurance companies to settle on ‘totaling’ the vehicle instead. If you’ve got a less expensive auto insurance plan, then you’re less likely to have airbag replacement cover.

Can I remove airbag fuse?


you can’t remove a fuse to disable the airbag

, even if it had one which it doesn’t, it still wouldn’t disable it. cutting the wires won’t disable it either, twisting them, altering the impedence, nope, its a fail safe device afterall.

How do you remove an airbag control module?

  1. First, find the SRS computer module. In most cars, it is under the center console that is between the two front seats, or center of the dash on the floor. …
  2. Disconnect the positive battery cable and wait 3 min.
  3. You are now safe to unplug the airbag control module harness wiring plugs.

Can you swap airbag module?


Airbags are not repaired and not repacked

. The airbag control module however can be reset to clear crash history and then can be used again instead of purchasing a new airbag control module.

How do you clear an airbag code?

  1. Put the key into the ignition and turn the switch to the “on” position.
  2. Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
  3. Repeat Steps 1 and 2 two more times.

How much is an airbag module?

The average cost for an airbag control module replacement comes

between $685 and $712

for most cars and locations. The labor costs for this procedure are estimated between $103 and $130, while the cost of the parts is more expensive at $582.

Rebecca Patel
Author
Rebecca Patel
Rebecca is a beauty and style expert with over 10 years of experience in the industry. She is a licensed esthetician and has worked with top brands in the beauty industry. Rebecca is passionate about helping people feel confident and beautiful in their own skin, and she uses her expertise to create informative and helpful content that educates readers on the latest trends and techniques in the beauty world.