If uL (
unbalanced load
) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
How do I fix the code on my Whirlpool Cabrio?
Always disconnect the washing machine's power supply before working on the appliance!
First press PAUSE/CANCEL
once to clear the Fault code from the Cabrio display. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea.
How do you drain a Whirlpool Cabrio Platinum washer?
- Press “Pause/Cancel” twice on the control panel.
- Press “Power,” and turn the cycle knob to “Drain & Spin.”
- Push “Start.” The washing machine automatically unlocks when the water has drained.
How do I reset my Whirlpool Cabrio Platinum?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally,
turn on the washer
and it should now be reset.
How do you fix an unbalanced washing machine?
If something has shifted, you can relevel a top-loading washer by tipping the washer forward, then placing it back on the floor. Front-loading washers level by turning a leg to raise or lower it. You may need to open the front access panel to loosen the lock nuts that control the legs.
How do I reset my Whirlpool Cabrio touchscreen?
- Press PAUSE/CANCEL twice to cancel the cycle. The washer will drain.
- Press POWER.
- Select the desired wash cycle.
- Select the desired Modifiers and Options.
- Press START.
What do you do when your Whirlpool washer won't drain?
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
Why does my Whirlpool washer not spin all the water out?
If your washer will not spin out all water and clothes are still wet,
the drain pump might be clogged with debris or possibly faulty
. There could be a foreign object that is stuck in the pump and inside the drain hose. Check these areas and remove anything that may be clogging the draining system on your washer.
Why won't my Cabrio washer fill with water?
Washing Machine Won't Fill Because
Water Inlet Valve
Defective. Washing machines have a water inlet valve that allows both hot and cold water into the unit. … No continuity indicates an issue with the valve. When the water inlet valve is the cause for a Whirlpool Cabrio washer not filling with water, it must be replaced.
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds.
When you turn it back on it should be reset
.
Is there a way to reset a whirlpool washer?
Method 1:
Unplug it
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Why is my washer shaking violently?
Your washing machine needs to stand level and balanced on its feet to function properly. An
unbalanced appliance will vibrate and shake during operation
. Try rocking the appliance from side to side or back and forth. If it's rocking a lot, your flooring or appliance's feet may be uneven.
How do you know if your washing machine is unbalanced?
If a top load washer's tub begins to bang against the sides of the washer when the spin cycle begins
(before reaching top speed), this indicates a likely unbalanced load. Just pause the cycle and arrange the clothes in the basket and try again.
