The floppy drive 4-pin power supply connector is
the standard floppy drive power connector
in computers today. The power connector itself is a Berg connector, sometimes referred to as a Mini-Molex connector.
What is an FDD pin?
FDD stands
for floppy disk drive
. Although most computers no longer use floppy drives, the FDD connector is still present on many motherboards. The FDD connector contains 34-pins, and uses a FDD ribbon cable to connect to a 3 1⁄2” floppy disk drive.
What is FDD connector for?
The floppy channel, FDD header, or floppy connection is
where the floppy drive connects to the computer motherboard
. In the picture below, is an example of a motherboard with two IDE connections and a floppy channel connector. Finally, the standard PC floppy drive connector contains 34-pin holes.
How many pins does a FDD connector have?
FDD data cables use a standard
34-pin
pinout (see Table 6-2), but connectors vary. 5.25-inch drives use a card-edge connector. 3.5-inch drives use a header-pin connector. Older standard FDD cables have at least three connectors, one for the FDD interface and two for drives.
What is a P4 connector?
1. The P4 connector is
a 12V power supply cable used with motherboards that have an Intel Pentium 4 or later processor
. Today, the connector is a standard power connector and is used with both Intel and AMD motherboards. … All of these wires attach to a four pin connection on the motherboard.
Do floppy drives use IDE?
Floppy drives don’t use a normal IDE
(PATA) connection; they use a special 34-pin connector. If your motherboard does not have this connector then you’ll need to get a USB floppy drive instead.
Do you need 4 pin CPU power connector?
4 pin is for extra stability when overclocking etc.
It is not necessary to use the additional
4 pin connector if you’re not pushing the board or CPU too hard. Basic everyday computing and gaming won’t require it. … It’s definitely not needed for normal operation or even a slight overclock.
What voltage does a floppy drive use?
All 3.5′′ floppy drives use
+5V solely
, the 12V on standard power connector simply not used.
For what can we use IDE connector?
IDE, an acronym for Integrated Drive Electronics, is a standard type of connection for storage devices in a computer. Generally, IDE refers to the types of cables and ports used
to connect some hard drives and optical drives to each other and to the motherboard
.
What is an EPS connector?
The EPS connector is meant
to supply power to a motherboard cpu socket
while the PCI express connector is meant to supply power to a GPU.
What is an ATA connector?
Serial ATA (SATA, abbreviated from Serial AT Attachment) is
a computer bus interface that connects host bus adapters to mass storage devices
such as hard disk drives, optical drives, and solid-state drives.
What is the purpose of 4 pin Molex connector?
The Molex connector is used
for power connections for a disk drive in a computer as well as for other computer components such as CD-ROM’s
, graphic cards etc. The Molex connectors bring DC power to the drives inside a PC case.
What is a 4 pin connector called?
The Molex 4-pin power supply connector is one of the standard peripheral power connectors in computers today. The power connector itself is a Molex 8981 connector called
the AMP MATE-N-LOK
.
How does a 4 pin connector work?
A four pin connector is a little different than the three pin connector since it has the extra (fourth)
wire used for controlling and sending signals to the fan
, which likely has a chip on it that tells it to slow down or speed up (in addition to the other wires the three pin connector has).
What type of connector is used for IDE PATA drives?
| Two ATA motherboard sockets on the left, with an ATA connector on the right. | Type Internal storage device connector | Production history | Designer Western Digital & Compaq, subsequently enhanced by many others | Designed 1986 |
|---|
