What Is An Acceptable Alternative To Installing An Audible Backup Alarm On Vehicles?

Instead of using a backup alarm, you can

install a camera system on the rear

of the vehicle that operates day and night.

When the height of workplace exceeds 30 feet above ground what safety device must be provided for workers?

Wall openings that are greater than 30” high and 18” wide need to be protected with

guardrails

when the bottom of the opening is less than 36” above the working surface and the fall is more than 4′. Ladder openings need to be guarded with off-set guardrails or swinging gate must be provided.

Can debris nets create a caught between hazard?

Safety nets often catch falling debris or equipment, which impacts their ability to safely arrest a fall. If left in the net while work is ongoing,

debris can damage a safety net system

or become a hazard to the worker if they fall.

Which of the following are considered acceptable methods of protecting workers?

The following measures can protect you from physical and health hazards:

safe work practices

, product substitution, engineering controls, training and communication, environmental monitoring, and personal monitoring.

Are reversing beepers legal requirement?

Reversing alarms

must not be strident and must not be used on the road if their sound is likely

to be confused with that from a pedistrian crossing. On the internet, you can be anything you want. It’s amazing that so many people choose to be stupid.

Is a backup alarm required by DOT?

As you may be aware,

OSHA has no requirements for back-up alarms

in the general industry standards, 29 CFR Part 1910.

What height is a harness required?

OSHA requires workers to wear a full-body harness, (one part of a Personal Fall Arrest System) when they are working on a suspended scaffold

more than 10 feet above the working surface

, or when they are working in bucket truck or aerial lift.

What are the three main protection methods against cave ins?

• SLOPE or bench trench walls.
• SHORE trench walls with supports, or.
• SHIELD trench walls with trench boxes.

What is the OSHA standard for fall protection?

OSHA requires that fall protection be provided at elevations of

four feet in general industry workplaces

, five feet in shipyards, six feet in the construction industry and eight feet in longshoring operations.

What must be done to ensure the safety nets are properly installed?

1. Nets must be installed as close as possible under the walking/working surface, but in no case will an employee be exposed to a fall greater than 30 feet into a net.
2. They must be installed in a manner that prevents a falling individual from striking any object below the net.

What are the four common types of struck-by hazards?

Be sure that examples of the most common struck-by hazards (

flying, falling, swinging and rolling

) are covered.

Which one of these methods is least acceptable for putting out an electrical fire?

Which one of these methods is not acceptable for putting out an electrical fire? Feedback:

Water

is not acceptable for putting out an electrical fire.

When should safety nets be installed?

Safety nets must be installed

as close as practicable under the surface on which employees are working

, but in no case more than 30 feet below. When nets are used on bridges, the potential fall area must be unobstructed.

What criteria must your employer provided PPE meet?

29 CFR 1910.132: General requirements says that all PPE has to meet these minimum requirements:

Provide adequate protection against the particular hazards for which they are designed

.

Be of safe design and construction for the work to be performed

.

Be reasonably comfortable when worn under the designated conditions

.

Where can I find OSHA standards?

OSHA standards are

published in Title 29 of the Code of Federal Regulations (CFR)

and are divided into separate standards for General Industry, Construction, and Maritime.

What type of safety measure would help a vehicle reverse safety?

They should be highly visible, and sensibly positioned. Where vehicles reverse up to structures or edges, barriers or wheel stops can be used to warn drivers that they need to stop.

White lines on

the floor can help the driver position the vehicle accurately.

What is a white noise reverse alarm?

White sound reversing alarms use broadband frequencies, giving greater directional information to the ear. This means the

sound is instantly locatable

– a huge leap forward in terms of safety, because even a split-second’s confusion can result in serious injury or death.

Are forklifts required to have backup alarms?

OSHA does not have a requirement that forklift vehicles be equipped with a backup alarm or

warning light (although these features are standard on most new equipment). … However, OSHA cautions that certain operating conditions may require the use of additional warning devices, such as backup alarms.

What is a backup alarm?

A back-up beeper, also known as back-up alarm or vehicle motion alarm, is

a device intended to warn passers-by of a vehicle moving in reverse

.

Why do trucks beep when they backup?

Everyone – no matter where you live here in Arizona – is familiar with that obnoxious “beep beep” sound commercial trucks and vehicles make when they’re backing up. This sound is

designed to alert passers

-by like pedestrians, cyclists and other vehicles when a truck goes into reverse. … You can listen to the sound here.

What must be done before a harness and lanyard are used?

Prior to putting on any harness,

it must be inspected

. Not just the new employee, but the employee who has been wearing the same harness and lanyard since the job started. Yes, this means all harness users must perform a daily inspection.

Do you need a harness on a ladder?

Portable ladders:

fall protection is not required for employees climbing

or working on portable ladders. Neither the ladder standard (29 CFR 1926, subpart X) nor the fall protection standard (29 CFR 1926, subpart M) requires fall protection for workers while working on portable ladders.

Does OSHA require a harness on a ladder?

The quick answer is

no

, but let me explain why. The OSHA standard for construction (29 CFR 1926.501) requires workers to use fall protection with an unprotected edge that is 6 feet above a lower level. … Neither standard requires fall protection for workers on portable ladders.

What is excavation OSHA?

OSHA defines an excavation as

any man-made cut, cavity, trench, or depression in the Earth’s surface formed by earth removal

. … In general, the depth of a trench is greater than its width, but the width of a trench (measured at the bottom) is not greater than 15 feet (4.6 m).

Which of the following is considered the safest of the four methods to prevent an excavation wall collapse?

Sloping and Benching

.

This method is considered the safest of the four methods. It involves cutting back the trench wall at an angle inclined away from the excavation.

What materials are used for excavation protection?

Shielding systems include

trench boxes, steel plates, and/or combination of protective systems

. Shielding does not protect against soil failures. They are intended to protect workers, not support the excavation.

What are the 3 types of falls?

• Physiological (anticipated). Most in-hospital falls belong to this category. …
• Physiological (unanticipated). …
• Accidental.

What are safety nets in construction?

Construction Safety nets are

used at high-rise building construction sites for preventing accidental fall of people or objects from the site

. Construction safety nets are the safest and cost effective fall prevention system in the world.

What important elements must be considered during the inspection of webbing lanyards and harnesses?

Pre-use checks should be tactile and visual

. The whole lanyard should be subject to the check, by passing it slowly through the hands (eg to detect small cuts of 1 mm in the edges, softening or hardening of fibres, ingress of contaminants).

What are the 4 types of fall protection?

All active fall protection for the construction industry falls into four basic categories:

fall arrest, positioning, suspension, and retrieval

. OSHA provides standards for each category of fall protection.

What are 3 types of fall protection devices?

• Positioning – These systems hold workers in place while leaving their hands free, to allow them to work. …
• Suspension – These systems lower and support workers while leaving their hands free for the activities they need to perform.

What is safety netting construction?

Safety netting offers

strength, impact resistance, and durability

to increase worker confidence. Construction safety netting systems catch personnel, debris or both, and are strong and durable for indoor or outdoor use. … Permanent and portable guardrail systems help keep workers a safe distance from fall hazards.

What type of system would a safety net be considered as?

Safety nets are classified as

a passive fall protection system

which can be installed as either a barrier to prevent a fall, or beneath the work to catch a falling worker. Safety nets are designed to decrease the fall distance, to absorb the energy of a fall, and to reduce the likelihood or seriousness of an injury.

What are the types of safety net?

• 1 – 4MM Knotted Layer Safety Nets.
• 2 – 4MM Machine Knotted Double Layer Safety Nets.
• 3 – 4MM Knotted + Mono Nets Type Safety Nets.
• 4 – 4MM Knotted Triple Layer Type Safety Nets.
• 5 – 6MM Knotted Double layer Safety Nets.
• 6 – 6MM Knotted + Mono Nets Type Safety Nets.

How many types of safety nets are there?

Safety nets are designed to have square or diamond meshes. There are

two different types

of safety nets. Knotted nets work by the principle of tightening the nodes when a load is placed on them. The tightening cannot be undone and the absorbing capacity of the net decreases.

What does PPE stand for?

Personal protective equipment

, commonly referred to as “PPE”, is equipment worn to minimize exposure to hazards that cause serious workplace injuries and illnesses.

What is acceptable when using powered tools?

Which is acceptable when using powered tools? … Use

only nonconductive tools and materials

.

What should you use to avoid injury from an impact hazard?

1. Provide safety eyewear. …
2. Enforce hardhats at work sites. …
3. Ensure workers are highly visible. …
4. Lower blades and lock moving parts of machines when not in use. …
5. Inspect tools and equipment. …
6. Limit access to work areas.

What are the elements of placing an installation in an electrically safe work condition?

• Identify power source. …
• Disconnect power sources. …
• Verify that power is off. …
• Lockout/tagout. …
• Verify again. …
• Discharge stored electrical energy (and install safety grounds under certain conditions)

Can you use flour to put out an electrical fire?

Flour should NEVER be used to extinguish a grease fire

. It could be ignited, making matters worse. Baking powder and baking soda are NOT the same thing, and like flour, will make a fire worse.

What to use to put out an electrical fire?

A fire extinguisher

is an ideal way to douse an electrical fire, and OSHA suggests having a working fire extinguisher on every floor of the home in the event of an emergency. It’s essential, however, that any extinguisher used to put out electrical fires is rated appropriately.