What Is The Bore And Stroke Of A 289?

by | Last updated on January 24, 2024

, , , ,

The 289 cu in (4.7 L) was also introduced in April 1963. Bore was expanded to 4.00 in (101.6 mm), becoming the standard bore for most small block engines.

Stroke remained at 2.87 inches

. The 289 weighed 506 lb (230 kg).

What can a 302 be stroked to?

Ford Based 302 Small Block, using a 3.400′′ stroke to achieve a displacement of

347 cubic inches

. A 347 has a little bit more bottom end than a 331 while adding additional horsepower from its larger displacement.

What’s the difference between 289 and 302?

The only difference between the 289 and 302 is the 302 has

a 1/8′′ longer stroke

.

How many horsepower is a 289 Ford engine?

The 289 (1963-1968) was a high-revving, pint-sized powerhouse producing

195 and 210 horsepower

in base trim (two or four barrel carburetor, respectively), and 271 horsepower in HiPo (High Performance) form.

Is 289 or 302 engine better?


There is not much difference between the two engines

.. The blocks are pretty much identical until you get up to the 5.0 roller blocks which have longer bores for the roller lifters… You can buy linked roller lifters to use in your early block if you want the roller cam in your 289..

How much HP can you get out of a 289?


500 hp

is the “generally accepted” limit on any 289-302 block.

What year did Ford stop making the 289?

The 302 replaced the 289 in

1968

and had a 27-year production run, primarily as a Mustang engine option. Ford manufactured the 351 in Windsor, Ontario, and in Cleveland, hence the “351W” and “351C” designations.

How much horsepower can you get out of a 302?

Standard Ford 289 and 302 small-blocks were factory-rated between 200 and 230 hp. The vaunted 289 High-Performance engine was said to make 271 hp. Today, if a 302 Ford makes

360 hp

on pump gas with a hydraulic cam, most experts consider it to be a pretty good motor-at least until Joe Sherman steps up to the plate.

How do I get the most power out of my 302?

  1. Install a performance aftermarket cold air intake to replace the Ford 302 factory air intake. …
  2. Install a performance aftermarket exhaust system to replace the Ford 302 factory exhaust system. …
  3. Install a forced induction — supercharger or turbocharger — kit.

How much horsepower does a 347 stroker have?

Horsepower:

500
Torque: 450 Bore/Stroke: 4.030 x 3.400 Compression: 10:1 Fuel Type: Pump Gas, 93 AKI (USA) / 98 RON

How can I get more power out of my 289?

You can change the intake to a quality dual plane manifold, add headers, increase you

cam’s lift and duration

, add quality aluminum cylinder heads, increase your compression (beef up the bottom end). You most cost effective way to build a 289 is to not.

How much horsepower does a 67 289 have?

Year 1967 “A” Code 1967 “K” Code Power (hp)

225 hp @ 4400 RPM

271 hp @ 6000 RPM
Torque (lb/ft) 305 lb/ft @ 3200 RPM 312 lb/ft @ 3400 RPM Compression 10.0:1 10.5:1 (65) Displacement 289 cu / 4.7 liters 289 cu / 4.7 liters

What Ford engine has the most horsepower?

The all-new

2020 Mustang Shelby GT500

will boast the most powerful Ford engine. This formidable supercharged engine will generate 760 horsepower and 625 pound-feet of torque. That means the revolutionary 2020 Mustang GT500 will be the most powerful street-legal Ford in history.

Is 302 a good motor?

The Ford 302 small-block is one

of the best-known engines

in the automotive world. We review its performance and design. Ford’s 302 engine began life in 1968 as a replacement for the smaller 289, thus ushering the Ford small-block into a new era.

Is 302 better than 351w?

So for equal money, a 351 will have more cubes, more low end torque, and a lower RPM peak. A 302 will have the same HP, but a slightly higher tq peak with lower tq numbers. In almost any situation,

cubes are better

.

How high can you safely Rev A 289?

If the engine is properly balanced it will spin up to virtually unlimited RPMs, but then the valvetrain will limit you. If you run hydraulic lifters you are pretty much limited to

6500 RPM

at best.

Rebecca Patel
Author
Rebecca Patel
Rebecca is a beauty and style expert with over 10 years of experience in the industry. She is a licensed esthetician and has worked with top brands in the beauty industry. Rebecca is passionate about helping people feel confident and beautiful in their own skin, and she uses her expertise to create informative and helpful content that educates readers on the latest trends and techniques in the beauty world.