Vise, also spelled Vice, device consisting of two parallel jaws
for holding a workpiece
; one of the jaws is fixed and the other movable by a screw, a lever, or a cam. When used for holding a workpiece during hand operations, such as filing, hammering, or sawing, the vise may be permanently bolted to a bench.
What is a modern tail vise?
Modern tail vise
It uses
steel plates
for its structure – one steel plate with the nut is mounted on the side of the bench, two others are built into a sliding jaw along with the bench screw. This is a robust design and it’s easier to install and adjust than the older style.
What is a wagon vise?
Clamping work to a bench surface between dogs is a very old technique. … The simpler of the two vises is often referred to as a wagon vise since
the moving dog travels in a block trapped within the bench top and rides along a pair of rails
, like a wagon or cart.
What is a Roubo workbench?
The Split-Top Roubo Workbench is
a modern twist on the classic Roubo design
, inspired by Plate 11 of Andre Roubo’s L’Art du Menuisier. … Whether you’re into hand tools, power tools, or both, this bench will serve all of your work-holding needs. This project is for the workbench only and does not include the cabinet.
How does the hovarter vise work?
Hovarter bench vise mechanism has
smooth, fast acting motion
. … A toothed transfer bar, mounted under the benchtop, synchronizes the clamping action on the two shafts, allowing one handle clamping, just like a chain-linked screw style vise, except this vise has the luxury of quick-acting slide rods.
Is a tail vise necessary?
The main reason why a traditional tail vise is so darn useful is
because of the unobstructed gap you get in the front of your bench
. this gives you the perfect way to solidly clamp chair legs, or any long part that needs to be held while you work on it from one end.
Why is it called a wagon vise?
Clamping work to a bench surface between dogs is a very old technique. … The simpler of the two vises is often referred to as a wagon vise
since the moving dog travels in a block trapped within the bench top and rides along a pair of rails, like a wagon or cart
.
What are the four vise rules?
- Do not weld the base of the vise to any metal.
- Do not repair a vise by welding or brazing.
- Do not try to bend a heavy rod in a light vise.
- Do not cut into the jaws.
- Do not apply heavy pressure at the corner of the vise jaws.
- Do not use a handle extension (e.g., a pipe) for extra clamping pressure.
What simple machine is a vise?
3.
The screw
is an inclined plane wrapped around a cylinder. It is used to hold items in place. Examples of the screw are: screws, light bulbs, jar tops and a vise.
When not in vise should you leave with?
46. Bench vises not in use should be left loose with
the handle in a vertical orientation
. This will prevent injury to those walking past the workbench.
What is the point of a split top workbench?
EFFORTLESS WORKHOLDING. The Split Top Roubo is widely used by professional furnituremakers, teachers and schools, as well as amateur woodworkers. It excels at holding work in the three most necessary positions:
for working edges, faces, and ends
. The Glide Leg Vise excells at working the edges of boards.
How much does a Roubo workbench cost?
And take a look at the Lie-Nielsen Roubo on the right. At
$3500
, this workbench will satisfy you in the way only the French variety can! For many (if not most) of you, woodworking is a hobby. That means its the place where you direct your disposable income.
How thick should a woodworking bench top be?
The top of a woodworker’s workbench is usually made of laminated hardwood; beech, maple, oak or ash. Professional level workbenches typically have a
three inch thick top
, but those can cost starting at $1,000 and run over $3,000.
What is a face vise?
Face vise. These come in two styles: one
with steel or cast-iron jaws
you can use as is or add auxiliary wooden jaws [Photos A and C], and the other with no jaws, requiring you to build wooden jaws [Photos B, D, and E]. The first typically costs more, but installs easier.
What is a leg vise?
Leg vises are characterized by
their vertical jaws operated by a single screw, placed below the clamping area and above the lower fulcrum part of the jaw
. … This form of vise probably evolved from the blacksmith’s iron post vise. Leg vises typically use the left front leg of the bench as the rear jaw of the vise.
