The clutch slave cylinder is
a component found on vehicles equipped with manual transmissions
. It works together with the clutch master cylinder to disengage the clutch when the pedal is pressed so that the transmission can be safely shifted.
How do you know if the slave cylinder is bad?
- Inability to switch gears.
- Low fluid level.
- Leaking of brake fluid.
- Clutch pedal goes all the way to the floor before working.
- Clutch pedal feels loose.
- Contaminated brake fluid.
How much does it cost to replace a slave cylinder?
Clutch Slave Cylinder Replacement Cost – RepairPal Estimate. Labor costs are
estimated between $110 and $138
while parts are priced between $95 and $106. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.
How do you test a clutch slave cylinder?
- Open the hood. Locate the slave cylinder.
- Look around the cylinder for wet spots that indicate it is leaking. If there is fluid coming from the cylinder, it needs to be replaced.
- Watch the cylinder as an assistant depresses the clutch pedal.
- Get in the car and start it.
Where is slave cylinder located?
Locate the slave cylinder. It is located
on top of the transmission
, is approximately four to six inches long. Trace the copper fluid line coming from the master cylinder to the slave. If you can’t see it from the hood, try locating it from under the vehicle.
Can you fix a slave cylinder?
There are two choices in servicing a slave cylinder:
overhaul or replace
. In the distant past, when slave cylinder bodies were made of cast iron, overhaul was a viable option. Currently, slave cylinder bodies are aluminum, so replacement is almost always the best option.
What happens when slave cylinder goes out?
If the clutch slave cylinder develops any sort of leak internally or externally it may
cause the pedal to feel spongy or mushy
. The pedal may also sink all the way to the floor and stay there when depressed, and may not be able to properly disengage the clutch so the transmission can be safely shifted.
How long does it take to replace slave cylinder?
How long does it take to replace a slave cylinder? To replace both cylinders takes
roughly 8 hours
. You can get an exact quote, both as to labor and parts, by using YourMechanic’s on-line estimator for clutch repairs.
What is the difference between a clutch master cylinder and a slave cylinder?
Clutch Master Cylinder is
connected directly to the clutch pedal
and is part of the hydraulic system that generates hydraulic pressure. … Clutch Slave Cylinder is used in the hydraulic clutch system and is usually mounted in the transmission, it can be found either on the outside or on the inside.
How much does it cost to replace a master cylinder?
The average cost to replace the master cylinder will be
around $320 and $500
, with the parts cost being between $100 and $210, and the labor costs to be between $230 and $300 on average.
What are signs of a bad clutch?
- Weak Acceleration. …
- Grinding Gears. …
- Loose Clutch Pedal. …
- Sticky Clutch Pedal. …
- Other Noises. …
- Won’t Shift into Gear. …
- Won’t Stay in Gear. …
- Burning Smell.
How do I know if my clutch has gone?
- Spongy, sticking, vibrating or loose clutch pedal when pressed.
- Squeaking or grumbling noise when pressed.
- Ability to rev the engine, but poor acceleration.
- Difficulty shifting gear.
What causes clutch failure?
Sudden and gradual failure
Sudden failure is most often caused by a
broken or loose clutch cable, linkable or a failed hydraulic master/slave cylinder
. There can also be leaks in the hydraulic line or even the disc could be contaminated with something like dirt or debris.
Should slave cylinder be replaced with clutch?
The clutch slave cylinder is part of the hydraulic clutch system and helps with clutch disengagement. … Signs that your clutch slave cylinder need to be replaced include:
You are not able to change gears when you are driving
.
Brake fluid is leaking around the clutch pedal
.
Do clutch kits come with slave cylinders?
If your vehicle has what is known as a Concentric Slave Cylinder (CSC). This type of slave cylinder is
part of the internal clutch mechanism
and is part of the replacement clutch kit.
How do you fill a clutch slave cylinder?
In order to pump up the clutch you need to fill the clutch master cylinder with
brake fluid
. Have an assistant push the clutch to the floor several times while the clutch is held open with the bleed screw on the clutch slave cylinder. Once the fluid is expelled then tighten the bleeder.
