What Kind Of Oil Does A 2002 Ford Explorer Take?

What kind of oil should I use in my 2002 Ford Explorer?

The two base engines the 4.0L V6 (non-flex fuel compatible) and the 4.0L V6 (flex fuel compatible) require 5 quarts of

5W30 synthetic oil

while the 4.6L V8 optional engine takes 6 quarts of 5W20 synthetic oil.

What type of oil does a Ford Explorer use?

The recommended oil type for the Ford Explorer is a

SAE full synthetic at a viscosity of 5W-30 and 0W-20

for vehicles with under 75,000 miles.

Can I use 5W-30 instead of 5W20 in my Ford Explorer?

If you put in 5W-30 oil instead of 5W-20 when the latter is the grade suggested by your vehicle's manufacturer,

damage to internal engine parts can occur

. … Additionally, your engine may experience performance issues such as diminished fuel economy and horsepower.

Can I put 10w30 In my Ford Explorer?

You are fine using 10w30

also. Good luck.

What kind of oil goes in a 2001 Ford Explorer?

Ford Explorer 2001,

SAE 5W-30 Synthetic Blend Motor Oil

, by Motorcraft®.

How do you reset the oil light on a 2002 Ford Explorer?

1. Crank the Explorer's engine or turn the key to the “ACC” ignition position. Push the “Setup” button to the right of the steering wheel. …
2. Push “Reset.” The screen will show “Oil Life – Hold Reset New”
3. Press and hold “Reset” for two seconds.

How much oil does a 2002 Ford Explorer take?

Capacity:

6 quarts (with filter)

When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase. After refill, check oil level.

What's the difference between 5w30 and 5W20?

When comparing 5w20 vs. 5w30 motor oil, the 20 indicates that the oil has a lower viscosity and is thinner at higher temperatures. … So, due to viscosity, 5w20 is a thinner oil during operating temperatures, whereas

5w30 is thicker during operating temperatures

.

Does Ford Explorer need synthetic oil?

The 2017 Ford Explorer

only uses synthetic oils

but the viscosity and capacities vary by engine type. The 2.3L 4 -cylinder engine uses SAE 5W-30 and can hold 5.7 quarts. The 3.5L V6 prefers SAE 5W-20 filter and holds 6 quarts.

Which oil is better 5w20 or 5w30?

When it comes to their higher operating temperature performance,

5W30 motor oil performs slightly better than 5W-20

and is a thicker oil than its counterpart. … Thus, it will protect your engine parts better under moderate oil pressure and high temperature settings.

What happens if I put the wrong oil in my car?

Using the wrong fluid can

cause poor lubrication, overheating, and possibly transmission failure

. A mechanic might not be able to reverse the damage, even by flushing the transmission. Mistakenly adding motor oil or brake fluid can also destroy your transmission.

Can I use 10w30 instead of 5w20?

Originally Answered: Can I put 10w30 instead of 5w20?

You can

, but you will get worse mileage, and in most cases shorten the life of your engine, as it will take longer to pump up pressure for your bearings and lifters, and won't spray your lower cylinders for an extra second or so on each cold start.

What kind of oil does my 2000 Ford Explorer use?

The three engine options for the 2000 Ford Explorer which are the 4.0L V6 SOHC, the 4.0L V6 (engine code X), and the 5.0L V8 all require 5 quarts of 5W30. However, Ford recently put out a service bulletin for the 5.0L V8 engine and now recommends using

5W20 synthetic oil

for this particular engine option.

What type of oil does a 2003 Ford Explorer use?

The 2003 Ford Explorer's two versions of 4.0L V6 engine (engine code [E] SOHC and [K] Flex) use 5 quarts of

5W30 synthetic oil

. The optional 4.6L V8 available in the 2003 Explorer requires 6 quarts of 5W20 synthetic oil.

What type of oil does a 1999 Ford Explorer take?

Ford Explorer Limited / Sport / XL / XLT 4.0L 1999,

SAE 5W-30 Synthetic Blend Motor Oil

, by Motorcraft®.

How much oil does a 2001 Ford Explorer take?

Capacity:

5 quarts (with filter)

When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase. After refill, check oil level.

Why does the service engine soon light came on Ford Explorer?

If the check engine light in your Ford Explorer starts flashing, that means that the

problem needs immediate attention

and your Ford should be transported in quickly. This blinking light usually indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system.

What transmission fluid does a 2001 Ford Explorer take?

Mobil 1 Synthetic Transmission Fluid Dexron/Mercon

1 Quart.

What type of oil does a 2001 Ford Explorer Sport Trac take?

SYNTEC Synthetic Motor Oil 5W-30

1 Quart.

How do you reset the oil change light on a Ford Explorer?

Turn the ignition to the ON position. Do not start the engine. Press and release the “Select/Reset” stem button on the instrument panel to toggle the options until the “

Hold Reset For Setup Menu

” option appears. Press “Select/Reset” to toggle the options until the “Hold Reset if New Oil” option appears.

How often does a Ford Explorer need an oil change?

An oil change is one of the most extensive and vital services for your car. Ford recommends getting your 2021 Ford Explorer oil & filter changed

every 3,000-5,000 miles

for conventional oil. Synthetic oil usually should be changed every 7,500 – 10,000 miles.

What brand oil does Ford recommend?

When it comes to picking a brand, nearly any brand of oil will do as long as it's the correct weight; however, Ford does prefer that its customers use

the Motorcraft brand of oil

.

Is 5W20 good for summer?

5W20 yeah it is like water, good for winter, but

not as good in summer

, when it gets 110F. Although 5w20 is like water, but it is holding together.

Is 5W20 good for winter?

5W20 motor oil is

another low-temperature grade typically recommended for winter use

, with a 10W-30 as an alternative for higher temperatures. This oil type is common because it provides the best fuel economy, saves fuel consumption, and has fewer exhaust emissions.

Can I put 5W 20 oil instead of 5W30?

Oil is rated to be used based on types of driving and temperatures driven in. If you check you're owners manual, you will find that both

5w20 and 5w30 can be used in your vehicle

. As there is really only a very slight difference in the two, you will be fine.

How many quarts of oil does it take for a Ford Explorer?

2019 Ford Explorer uses a synthetic oil. The 2.3L 4 -cylinder runs on 5W-30 and the 3.5L V6 prefers 5W-20. Both engines have a capacity of

6 quarts

, with a fresh filter.

Does 10w30 hurt 5w30 engine?

Most oils will mix perfectly, provided they have a similar synthetic. Therefore, there is no problem in mixing 10w30 and 5w30 since one will be topping up. Mixing the viscosity of oils will not have any effect on the engine. 5w30 and 10w30 engine oils have close viscosity, and thus

there is no harm in mixing them

.

What oil is thicker 5W-20 or 10W-30?

5w20

works within the temperature range -30 degrees to 35 degrees celsius, whereas 10w30 works within the temperature range -18 degrees to 30 degrees celsius. 5w20 is thinner at lower temperatures, whereas 10w30 is thicker at lower temperatures.

Why does Ford recommend synthetic blend?

With synthetic blend oil, you virtually get the best of both worlds. Mixing aforementioned oils

delivers less volatility for increasing fuel economy and heightened high-temperature performance

. So, it is especially great for, say, your F-Series or any other Ford pickup truck or SUV.

What is SAE 5w30?

5w30 is a

motor oil

that is widely used in light-duty petrol and diesel engines. Like most motor oils produced today, 5w30 is a multi-grade oil, meaning it ranges from a lower viscosity grade of 5 to a higher viscosity grade of 30.

Can I put 10W40 instead of 5w20?

In a 5W20 engine. You could use a

0W20 oil

(I use 0W20 oil) in cold weather and it would be Ok by Ford. (they will not say it is good, but they will still honor the warranty..) But 10W40 is way off, and I bet they would be not so happy over any engine problems if they found 10W40 in a failed engine.

Is 10w30 good for high mileage?

Mobil Clean High Mileage 10W-30 is designed for vehicles with

more than 75,000 miles

. Its advanced formulation helps protect seals and prolong engine life. … These oils protect against sludge and engine rust and corrosion under high and low-temperature operating conditions.

Is 5W-30 good for high mileage?

5W-30 motor oil is the top viscosity recommendation by automakers over the past four decades for use in many vehicle types. … Furthermore, high-mileage 5W-30 motor oil is specially formulated for late model vehicles or newer vehicles with

over 75,000 miles/120,000 kilometers

.

What are the signs of low engine oil?

• Oil pressure warning light.
• Burning oil smell.
• Strange noises.
• Weaker performance.
• Overheating Engine.

What happens if I use 20w50 instead of 5w30?

20w50 is

actually thicker than 5w30

. This will result in less fuel efficiency, less horsepower, and more engine damage because it will have to work harder to rotate. Trust the engineers that made your vehicle.

What happens if I use 10w40 instead of 5w30?

If you use 10-w-40 instead of 5-w-30 specified by the manufacturer then the viscosity of 10-w-40

used by you will be higher and oil thicker than what is specified during winters

. Similarly the oil viscosity will be higher and oil thicker than specified during summers.

What kind of transmission fluid does a 2000 Ford Explorer take?

Mobil

1 Synthetic Transmission Fluid Dexron/Mercon 1 Quart.