What might happen if the trailer is too high when you try to couple? If the trailer is too low, the tractor may stike and damage the trailer nose; if the trailer is too high,
it may not couple correctly
. … If there is space something is wrong and the trailer would come loose very easily.
How can I make sure my trailer height is correct before coupling?
How do you check to make sure trailer height is correct before coupling?
It must be slightly lower than the center of the fifth wheel
, so trailer is raised slightly when dolly is pushed under.
What might happen if the trailer is too high?
In addition to incorrect coupling, if a trailer is too high off the ground and you try to back into it, you
may cause damage as the rear of your truck cab could strike the front of the trailer
. Further, the trailer king pin may become stuck in front of the fifth wheel plate which can be a costly and time wasting error.
Should you look into the back of the fifth wheel to see if it is locked into the Kingpin?
You should look into the back of the fifth wheel to see if it is locked onto the kingpin. …
Go under trailer
and look into the back of the fifth wheel. Make sure the fifth wheel jaws have closed around the shank of the kingpin.
Which shut-off valves should be open?
The rear shut-off valves
should be open. … When starting a trip, be sure that all shut-off valves are in the open position, except for the last valves on the rear trailer. It is important that air reaches the brakes on all trailers and that the air is not able to escape from the back of the vehicle.
How do you know if your trailer is equipped with ABS?
Remove a tire and look for the
ABS sensor on the axle
. Trailers and converter dollies built on or after March 1, 1998 are required to have Anti-Lock Braking Systems (ABS). This will be indicated by the presence of a yellow malfunction lamp.
How can you test the trailer emergency brakes?
How can you test the trailer emergency brakes?
Charge the trailer air brake system and check that the trailer rolls freely then stop and pull out the trailer air supply control pull gently on the trailer with the tractor
to check that the trailer emergency brakes are on.
How can you test the airflow to all trailers?
Check air flow to all trailers:
Use the tractor parking brake and or chock the wheels to hold the vehicle
. Wait for air pressure to reach normal, then push in the red “trailer air supply” knob. This will supply air to the emergency (supply) lines. Use the trailer handbrake to provide air to the service line.
What gear should the tractor engine be in after you uncouple the trailer and are inspecting the trailer supports?
| Question Answer | What gear should the tractor engine be in after you uncouple the trailer and are inspecting the trailer supports? Neutral | You have coupled with a semitrailer. Where should you put the iron trailer supports before driving away? Fully raised with the crank handle secured in its bracket. |
|---|
What's a converter dolly on a tractor trailer?
converter dolly” means
a trailer with 1 axle group or single axle, and a fifth wheel coupling
, designed to convert a semi-trailer into a dog trailer. Converter dolly, equipped with between one and three axles and designed to connect to a towbar on the rear of the truck or trailer in front.
When not pulling a trailer Why is it a good idea to lock the glad hands together?
Why should you lock the tractor glad hands (or dummy couplers) to each other when you are not towing a trailer?
A The connected brake circuit becomes a back up air tank
. B If you did not, you could never build system pressure.
What should you do to stop a trailer skid?
Quote From The CDL Manual:
When a front-wheel skid occurs, the only way to stop the skid is
to let the vehicle slow down
. Stop turning and/or braking so hard. Slow down as quickly as possible without skidding.
Which trailer is most likely to turn over when you turn suddenly while pulling double trailers?
When you turn suddenly while pulling doubles, which trailer is most likely to turn over?
The rear trailer
is twice as likely to turn over as the tractor.
Which shut off valves should be open and which one should be closed?
The shut off valves, when in the open position, allows air to flow out to another trailer. If you're only pulling one trailer, the shut off valves
should always be closed
or else the air will simply escape out the back of the trailer.
How do I know if my hot water valve is open or closed?
If the handle on top is parallel to the valve, it's open
. Likewise, if the handle is perpendicular to the top, the valve is closed. Common places you might find a ball valve are in irrigation and in sites where you need to control water supply from one area to another.
Where are shut off valves located?
Locating the proper valve
Basements – the shut-off valve is typically located
near the front foundation wall
. The main water may come through the concrete floor or through the wall. The valve is typically within three to five feet of where the main water enters.
