- Don't use file with no handle.
- The work must be a little under the height of the elbows or on 40 to 44 inches as of the floor.
- Use just a file by sharp teeth.
- Grasp the lever of the file by the right hand and hold the palm against the end of the handle by the thumb on crest.
What is the main precautions to remember when using a file?
Files/Rasps
Do not use a file as a pry bar, hammer, screwdriver or chisel. When using a file or a rasp,
grasp the handle in one hand and the toe of the file in the other
. Do not hammer on a file.
How do you use files safely?
Hold the file firmly and securely with both hands where possible. When filing,
apply pressure on the forward or pushing strokes only
. The file teeth will dull quickly if excess down force is applied on the return stroke. NEVER use a file for prying or hammering.
What are the 6 precautions or measures that you should consider before the use of power tools?
- Read the instruction manuals and warning. Power tools come with safety information that is relevant to the handling of the equipment. …
- Invest in and use safety gear. …
- Inspect the tools for disrepair. …
- Clean and properly mark the work space.
What are the risks of using a file tool?
Potential hazards: The biggest hazard when using a rasp or file is the tang. The tang is the pointed tip in the handle position. If you do not place a handle over the tang before use, you have a good chance of puncturing your hand or any other part of your body with it.
Never use
a rasp or file without a handle.
Which way do you use a file?
With your opposing hand place your palm onto the tip of the file. Your palm is used to help press down while your dominant hand is used to guide and control the direction of the file. Rather than press hard for aggressive cuts switch to a more aggressive (coarse) file. Pressing too hard will dull the file more quickly.
What are the type of files?
- JPEG (Joint Photographic Experts Group) …
- PNG (Portable Network Graphics) …
- GIF (Graphics Interchange Format) …
- PDF (Portable Document Format) …
- SVG (Scalable Vector Graphics) …
- MP4 (Moving Picture Experts Group)
Who uses a file tool?
A file is a tool used to remove fine amounts of material from a workpiece. It is common in
woodworking, metalworking, and other similar trade and hobby tasks
.
Why should you never use a file without a handle?
Files are sometimes produced and sold without handles. This is because
handles can often outlast files
. Once a file is blunt, it's cheaper to replace it than it is to sharpen it or re-cut the teeth. … These files are referred to as solid handle files and will not fit inside other handles.
How do you use nail files?
Start from one of the outside corners
and file toward the center
. Don't file back and forth across the entire nail tip because it can damage the nail. When you achieve the desired length and shape on one side, file from the opposite corner toward the center. Go slowly.
What are the five safety rules?
- Disconnect completely. Meaning that the electrical installation must be disconnected from live parts on all poles.
- Secure against re-connection. …
- Verify that the installation is dead. …
- Carry out earthing and short-circuiting. …
- Provide protection against adjacent live parts.
What is safety measures in power hand tools?
- Keep floors dry and clean to avoid slipping while working with or around dangerous tools.
- Keep cords from presenting a tripping hazard.
- Never carry a power tool by its cord.
- Use tools that are double-insulated or have a three-pronged cord and are plugged into a grounded receptacle.
What are the five basic safety rules for hand and power tools?
- Keep all hand tools in good condition with routine maintenance.
- Use the right tool for the job and within its intended purpose of design.
- Examine each tool for damage prior to use and never use if damaged.
- Operate tools within the manufacturer's guidance.
What safety precautions should be taken when hand Hacksawing?
Hold stock being cut firmly in place
. Use a helper, a supporting bench or vise to support long stock if required. Keep teeth and blades properly set. Protect teeth of saw when not in use.
What is the first thing you should do when chiseling filing or cutting a material?
Make
sure that the cutting edge is sharp
. Dull chisels can be difficult to control and require more effort to do the job. Check the stock (wood) thoroughly for knots, staples, nails, screws or other foreign objects before chiseling. Clamp stock so it cannot move.
