The best way to cut a 4×4 post is by using a
12-inch miter saw, 10-inch radial arm saw
, both of which can cut completely through a post in one pass, or a standard circular saw that can make precise cuts in two passes with the help of a simple jig.
Can you cut a 4×4 with a 10 miter saw?
A 10 inch miter saw will cut through a 4×4 piece of wood perfectly. However,
you cannot cut in one go
. If you are using a stationary saw, you will have to flip over the material and cut it from the other side. If you want a miter saw that can cut through a 4×4 in one go, then a 10-inch size is not the ideal one.
Will a 10in miter saw cut a 4×4?
A 10 inch miter saw will cut through a 4×4 piece of wood perfectly. However,
you cannot cut in one go
. If you are using a stationary saw, you will have to flip over the material and cut it from the other side. If you want a miter saw that can cut through a 4×4 in one go, then a 10-inch size is not the ideal one.
What size wood can a 10 inch miter saw cut?
Saws start to differ when you look at their blade diameter—commonly 10 inches or 12 inches. The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a
2 x 6 at 90 degrees and a 2 x 4 at 45 degrees
; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.
Will a 7 1 4 miter saw cut a 4×4?
You won’t get through a 4×4 in one cut
with a 7-1/4′′ (max cut size will be less than (blade size – arbor size) / 2 = (7-1/4 – 5/8)/2 = less than 3-5/16′′). It’s not just a 4×4 you can’t cut; you can’t even cut a 2×4 (unless the saw has rails the blade pulls on).
How thick can a Mitre saw cut?
Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights. This larger saw can cut a maximum thickness of
3 1/2 inches
, enough to cut through four-by-fours.
Can I cut 4×4 with miter saw?
It may surprise you to know that the answer in question to cutting 4×4 posts with a miter saw is a hard,
YES
! … Sliding miter saws have more range of motion, because you can tilt the head of the miter saw forwards. This obviously tilts the blade forward, thus increasing the cutting capacity of the miter saw.
How deep can a 7 1/4 inch circular saw cut?
Circular Saw Sizes
Standard-size saws use 7 1/4-inch blades and can cut a maximum depth of
about 2 1/2 inches
.
What is the difference between a miter saw and a chop saw?
Whereas chop saws are rugged and relatively simple tools, mitre saws are designed and manufactured
to make precision cuts at many different angles
. Although a mitre saw can cut non-ferrous metal when used with the correct blade, they are most often used by joiners, kitchen fitters and cabinet makers to cut wood.
Will a 12 inch miter saw cut a 6×6?
The bevel ranges max out at 45 to 48 degrees. …
No
saw could cut through a 4×4 at a 45-degree bevel angle, nor could any cross-cut a 6×6.
Can I use a 7 inch blade on a 10 inch miter saw?
Yes you can
.
The only real difference, besides maximum cutting depth, is that smaller blades are often thinner and have a narrower kerf. I was curious if this could make them unsafe to run at the same speed as a larger blade, but actually the opposite is true.
Can I use a miter saw as a chop saw?
Miter saws and chop saws are not the same, even if the descriptions may sound similar. A chop saw is
used for straight precision cuts
, and a miter saw is used for angled cuts. Though it’s tempting to try to adjust the miter saw to work as a chop saw, the results will not be as good.
Is a 7 1 4 miter saw too small?
A 1/4
” wrench is too small for
3/8′′ nut, but it works perfectly on a 1/4′′ nut. A 7 1/4′′ saw works just fine to cut material thin enough for the capacity it will handle. If you are doing a lot of trim on a job site they are lighter to handle than most 10′′ models and have a greater cutting width than a 10′′ chop saw.
Can you put a 10 inch blade on a 12 inch miter saw?
You can put your 10-inch blades on your 12-inch saw (assuming the arbor holes are the same size), but
you cannot put 12-inch blades
on a 10-inch saw. The 12-inch saw gives you greater versatility – with the larger blade, it’s the hefty workhorse, and with the smaller blade, it’s a master of precision.
