What Size Tires Does A 2008 Ford Explorer Have?

What size tires can I put on my Ford Explorer?

An upgraded

20-inch

wheel size is standard on most Ford Explorer models.

What lug pattern is a 2008 Ford Explorer?

Can you put on different size tires?

Wheels and tires are not interchangeable words. Tires are a part of the wheel setup. For instance, your vehicle has a set size of rims, but you can buy different sizes of tires to fit those rims, as

long as the middle of the tires is the correct size

.

Will 33s fit on a Ford Explorer?

List of factory tire sizes of Ford Explorer and their equivalent in inches. … As you see the factory tires are just a little smaller, so fitting 33s and

35s would require a 3-5′′ lift depending on the generation

.

Can you put bigger tires on Ford Explorer?

Elite Explorer

When changing tire sizes, it is a common

rule not to exceed a maximum diameter variance of 3%

compared to the OEM size. The OEM on the XLT is an 18′′ wheel with a 20′′ as an option.

What size is 235 75R15 in inches?

Do all Fords have the same bolt pattern?

When it comes to Ford wheels (including Mercury and Lincoln), it also comes down to

two common five lug bolt patterns

, 5×4-1/2 and 5×5-1/2, although Ford did produce a few passenger cars with 5×5-inch bolt pattern.

How do you read a tire size?

The

two-digit number after the slash mark in a tire size is the aspect ratio

. For example, in a size P215/65 R15 tire, the 65 means that the height is equal to 65% of the tire’s width. The bigger the aspect ratio, the bigger the tire’s sidewall will be.

What cars use 5×114 3 bolt pattern?

The most popular cars with PCD 5×114,3 are:

Honda Civic oraz Accord

, Nissan Qashqai, Dacia Duster, Hyundai i30 and x35, Renault Megane III and Laguna III, Kia Cee’d, Sportage and Venga, Mitsubishi Lancer, Outlander and ASX, Toyota Auris and Avensis III, Citroen C-Crosser, Suzuki SX4, Fiat Sedici, Mazda 3.

Can I use 60 instead of 55 tires?

Most likely yes

. The 55 or 60 in this case is the aspect ratio. It’s how tall the tire is as a percentage of its width. A 60 means the tire’s sidewall height is 60% of the width of the tire.

Can I use 235 tires instead of 225?

The difference between 225 and 235 tires is that the width of 225 tires is 225mm. On the other hand, 235 tires have a width of 235mm. 225 tires are mostly recommended for smaller cars while 235 tires are recommended for bigger cars. 225 tires are 225mm wide tires that are generally used for light vehicles.

Can I use 60 instead of 65 tires?

Physically,

yes they will fit

. It is recommended to stay within 3% of the original tire size on the car though. The size you have is 3.09% smaller, so not recommended.

When did the explorer change body style?

2002–05

Explorer

For 2002, Ford put a larger, all-new body on a unique platform.

What is the biggest tire you can put on a 2017 Ford Explorer?

What’s the biggest tire you can put on a Ford Explorer?

Active Member. the widest you will want to go on a 9′′ rim will be

285

. Even then, the tire mfgs recommend a 9.5′′ wheel for 285. of course you can find folks that go wider but its generally a bad idea.

Are 295 tires the same as 33?

You are correct.

The 295 is a true 33

, the 33×12. 5 is just over 32′′ mounted.

Will Ford 6 lug rims fit?

Car and truck wheels come in all sorts of different sizes and styles. Each wheel has a bolt pattern drilled into it which is specific for that vehicle. These bolt patterns don’t often crossover, so if you have wheels from a Chevrolet,

the bolt pattern will often not work on a Ford vehicle

.

How tall are p235 75R15 tires?

What is the size difference between 245 and 265 tires?

The difference between 245 and 265 is

ten millimeters

. Along with all the changes, it is understandable that the number 245 is changed to 265. You may have heard that bigger tires have to do with the speed of a car.

Is 8×6 the same as 8×6 5?

This bolt pattern is also commonly referred to as a 8×6. 5′′ bolt pattern. There is

no

difference between these fitments, just simply one is stated in millimeters (8×165.

What does 8×6 5 wheels fit?

The 8×6. 5′′ bolt pattern has been used on the

Dodge Ram 2500 & 3500

dating back to 1946, Ford F250 & F350 trucks from 1955 to 1998, and also the Chevy & GMC 2500 & 3500 trucks from 1967 to 2011. The Hummer H2 has also shared the 8×6. 5′′ wheel bolt pattern.

What does 50r mean on tires?

50 is the two-figure aspect ratio. This percentage compares the tire’s section height with the tire’s section width. For example, this aspect ratio of 50 means that

the tire’s section height is 50% of the tire’s section width

. R indicates the construction used within the tires casing. R stands for radial construction.

What does XL mean on a tire?

Some vehicles are equipped with “XL” tires. It doesn’t mean that they’re extra large, but it does mean that they are

extra-load tires

. The load index on these tires is much higher than a standard-load tire, which is why it is important to replace an XL tire with another XL tire.

What does Zr mean on a tire?

Tire Speed Rating Chart

For tires with a maximum speed capability higher than 240 km/h (149 mph), a “ZR” may appear in the size designation. Tires

with a maximum speed capability higher than 300 km/h (186 mph)

, require a “ZR” in the size designation.

Are 5×114 3 and 5×4 5 the same?

Backspacing and offset measurements are

the same for both

websites. Thank you for you time.

Which tire is wider a 65 or 70?

The series number in a tire-numbering system refers to the aspect ratio of the tire’s sidewall height to its width.

A series 65 tire’s height is 65 percent of its width

, a series 70 tire’s height is 70 percent of its width and so on. These differences in height affect both performance and safety issues while driving.

How much taller is a 65 tire than a 60?

The 65% aspect ratio (as in 235/65/17), compared to 60%, adds almost

12 mm (1/2′′)

to the radius of the tire (0.65-0.60)*(235mm)=11.75mm.

What does 60 R mean on a tire?

60 is the two-figure aspect ratio. This percentage compares the tire’s section height with the tire’s section width. For example, this aspect ratio of 60 means that the tire’s section height is 60

% of the tire’s section width

. R indicates the construction used within the tires casing. R stands for radial construction.

What does 5×114 3 mean?

The bolt pattern or bolt circle is the diameter of an imaginary circle formed by the centers of the wheel lugs. … A bolt circle of 5×114. 3 mm would indicate

a 5 lug pattern on a circle with a diameter of 114.3mm (or 4.5′′)

.

Will 114.3 rims fit 115?

There

is a definite difference between 114.3 and 115

– its not just rounding. 1 inch is exactly 25.4 mm – so 4.5 inch is exactly 114.3 mm. They are very close though yes.

What does 55 mean on tires?

The “55” grouping is the aspect ratio and is by far one of the most misunderstood dimensions. This is

the height of the sidewall from wheel to tread relative to the width

. Manufacturer’s represent this measurement in a percentage, so in our example, the sidewall is 129.25 millimeters — 5.08 inches — tall (235 x 0.55).

Can you change tire size on the same rim?

You can change the size of your tires with the same rims,

as long as the tire and rims have the same internal diameter

. Tires are flexible, however, so the width and height may be changed. … The key to changing your tire size is to understand how tire specifications work.

Can front and rear tires be different sizes?

Long story short: Yes,

it is a problem to have two tires of different sizes

on the front (or back) of your car. Having two different-sized tires on the same axle is generally not a good thing. … Sometimes, people choose to put larger tires on the rear axle of their vehicle for handling reasons, cosmetic reasons, etc.

Do bigger tires give a smoother ride?

Avoid bigger wheels

if you want a smoother ride.

As a general rule, bigger wheels result in a rougher ride. Switching to a smaller wheel and a thicker tire can give you a smoother ride without any major modifications to your car.

What does P235 mean on a tire?

Size: P235/65R17 is a common one. P denotes

passenger-car tire

. Some may start with an LT prefix, used on heavy-duty trucks. The number 235 is the cross-section width in millimeters, and 65 is the ratio of sidewall height to cross-section width (65 percent).

Should I change all 4 tires?

Some manufacturers of all-wheel-drive vehicles recommend that all four tires be replaced, not just one or two, because a new tire will have a larger overall diameter than the other tires. … The best approach, though, is to

replace all four if the tread on the old tires is significantly worn

.