Keep the forks
6 to 10 inches above the ground
to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
How high should forks be?
Forks: Driving
A properly trained operator will carry his forks or load
4-6 inches off the ground
. This position is high enough to reduce contact with dock plates, expansion joints in concrete, uneven areas, slight slopes, inclines and debris on operating surfaces.
When leaving a forklift parked the forks should be?
Lower the forks to the floor when parking the forklift. Make sure
that the forks touch the ground when you
are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.
When driving an unladen lift truck How should the forks be set?
When driving an unladen truck the forks must be positioned
as low as practicable and tilted back
. To comply with the manufacture’s stated lifting capacity the truck’s mast must be in the vertical position with the truck on level ground.
How far should you stand from a forklift?
The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s
about 20 feet
between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.
What will make the load more stable during travel?
When traveling with a load, always make sure
to tilt the mast of the forklift backward
so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.
When traveling with empty forklift the forks should be in what position?
Keep the forks
6 to 10 inches above the ground
to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
Is it illegal to leave keys in a forklift?
You might not be aware but
it is actually illegal to leave the keys in an unattended Forklift
. This measure is to prevent unauthorised use of the Forklift. … All forklifts and plant equipment can be fitted with low cost Driver Identification systems which prevent unauthorised usage.
Where can you not park a forklift?
Never park or leave the forklift in
any doorway
, entrance, emergency exit or in front of fire extinguishing equipment.
How should you normally drive a forklift?
- Always drive unloaded forklifts with the forks downgrade.
- Never drive a loaded forklift with the load downgrade.
- When driving up a ramp, drive loaded forklifts forward with the load upgrade.
What is the ideal way to pick up a loaded pallet?
To have a safe lift, have
the pallet close to the front wheels
. Keep the forklift mass in upright (90 degrees) position before inserting the forks into the pallet. Align and centre the fork ‘arms’ evenly from the centre stringer. Tilt the forks a little backwards to ensure its maximum security.
What is the recommended load height when traveling with a load?
Lower the load so that its lowest point is
15 to 20 cm
(6 to 8 inches) from the floor. While traveling, keep the load at a safe travel height. See Traveling & Maneuvering.
What is the minimum safe distance to drive behind another forklift?
Falling distance of an object from a pallet or 15 feet,
5 Feet both sides
, 5 Feet Rear of Forklift. do so (ALL CLEAR). Do not pass under the forks while in operation.
How many forklift lengths should you maintain between your forklift and another forklift traveling in front of you?
A safe distance shall be maintained approximately
three truck lengths
from the truck ahead, and the truck shall be kept under control at all times. 1910.178(n)(4) – The driver shall be required to slow down and sound the horn at cross aisles and other locations where vision is obstructed.
How many feet do you use to drive a forklift?
You should have
two feet and a hand or two hands and a foot
in contact with the vehicle at all times. Make sure your arms and legs are inside the vehicle at all times, and always use the operator’s restraint system.
Can a fully loaded forklift use its brakes to the maximum?
Braking control
Another important aspect of speed limitations is safe braking distances which must be considered when planning out any forklift travel paths in the workplace. …
A loaded forklift cannot be expected to stop at its maximum capabilities as the load itself can cause the forklift to tip or slide
.
