When entering the freeway using the acceleration lane or on-ramp, you’ ll want to accelerate to the speed of traffic on the freeway . Use the length of the acceleration lane to get up to speed, put your turn signal on to indicate that you are merging, wait for a large enough gap in traffic, and merge when safe to do so.
When entering the expressway in the acceleration lane you should?
After entering the entrance ramp , you should move into the acceleration lane. This is the lane that runs alongside the main roadway. In the acceleration lane, you can adjust your speed to the speed of the expressway traffic until it is safe for you to merge into traffic.
When entering an expressway in the acceleration lane a driver should quizlet?
slow or stop before entering the acceleration lane or expressway. should plan for fuel, food, and rest . a minimum of three seconds. the lane will be closed farther ahead.
When entering an expressway never stop in the acceleration?
When entering an expressway, never stop in the acceleration lane unless traffic is: Too heavy for you to merge safely .
What is important when you are getting into the acceleration lane?
Use the ramp and acceleration lane to increase your speed to match the speed of the vehicles on the highway . As you are speeding up, watch for an opening in the highway traffic. ... DO NOT stop at the end of an acceleration lane unless traffic is very heavy and you have to stop.
What is the best procedure to use when entering an expressway?
- Look for the freeway entrance sign. ...
- Make sure that you are not entering the freeway exit ramp. ...
- Follow the freeway entrance’s speed limit. ...
- Follow the freeway entrance’s ramp meters signal lights. ...
- Accelerate to a safe speed close to the flow of freeway traffic. ...
- Merge into the freeway lane.
When entering an expressway you need to?
Bring your vehicle to a complete stop before entering the highway if no other vehicles are present. Unless absolutely necessary, you should always avoid bringing your vehicle to a complete stop before entering a high-speed expressway. Enter the expressway and merge with other traffic as safely as possible.
What four steps should you follow when exiting an expressway?
What steps should you take when exiting an expressway? * At least 1/2 mile from exit signal and make lane change to position 3 when safe to do so. *Flash brake lights to warn drivers behind you. Keep a safe distance, monitor you front and rear zones.
When entering directly onto a freeway no acceleration lane you should?
Use the shoulder of the main road to get up to the speed of traffic. C. Speed up and enter the interstate only after you have identified a gap in traffic . When entering the interstate on a short entrance ramp where there is no acceleration lane, speed up only after you have identified a gap in traffic.
What is the first thing a driver should do after deciding to turn?
First you will need to stop at the stop line , make sure that you do not interfere with pedestrians, bicyclists, or vehicles moving on their green light, and make a turn. If a street has a left turn lane, you must use it when you turn left.
When you want to turn how far must you signal?
Before you stop, turn or change lanes, let the other drivers know what you are going to do by signaling. You can signal with your hand and arm or with your vehicle’s turn signals and brake lights. You should signal at least 100 feet before you turn so the other drivers can be ready.
How do you know if you are driving too slowly?
Are driving below 35 mph at any time. Are driving below the posted speed limit .
Where is it unlawful to overtake and pass?
The driver of a vehicle shall not overtake and pass upon the left , nor shall any driver of a vehicle drive upon the left side of, any interurban electric or street car proceeding in the same direction whether the street car is actually in motion or temporarily at rest, except: (a) When so directed by a police or ...
What is the greatest danger on expressways?
Rear end collisions are the greatest danger on expressways. Always leave room for emergency stops.
What are four possible problems you may have when entering an expressway?
Problems When Entering Expressway
General problems associated with expressway entrances include heavy traffic, short ramps and acceleration lanes, and high walls that may block visibility . Also, traffic ahead on the ramp may slow or stop abruptly.
What is the safest speed to use when you are merging onto the freeway?
C. The posted speed limit for freeway traffic. When merging onto a freeway, you should enter at or near the speed of traffic .
