The location of the airbag module differs from vehicle to vehicle, depending on the make and model of it. In some vehicles, it is located in the center console, kick panel, under the radio, or behind the steering wheel. Generally, though, it can be found
underneath the driver’s seat or front passenger’s seat
.
How do I know if my airbag module is bad?
Symptoms of a failing airbag sensor
You can easily tell if the sensor is functioning if the
airbag warning light on the dashboard is illuminating every time
you start the vehicle. But, if the airbag warning light stays illuminated after starting the vehicle, this is an indication of an airbag sensor problem.
Can airbag module be reset?
All airbag control modules can be reset and reprogrammed
, with the exception of flood, fire or hardware damage.
Can you drive without airbag module?
While a vehicle can still run without an airbag module, it is strongly recommended that
drivers do not operate the vehicle without it being installed
—unless an emergency situation arises and there is no other option. … Without airbags deploying, a driver and any passengers can face severe injury or even death.
What module controls the airbags?
An SRS airbag module, also known as the airbag electronic crash unit, controls the airbag’s deployment, stores crash data and exchanges information with the car’s engine.
How do you check airbag codes?
The airbag codes are double digit numbers. To read the codes,
count the number of times the light flashes, wait for the pause and count the flashes again
. For example, two flashes, a pause and four flashes mean that your airbag system’s problem is a code 24.
How much does it cost to reset airbag module?
Expect to pay between $80 and $120 to repair a pretensioner and even more to replace with new components. At the very least, the ECU or airbag module will need to be reset costing
about $50 to $150
. If the airbag control module needs replacing, expect to pay anywhere from $400 to $1,200 for a new one.
How do you reset the airbag?
- Put the key into the ignition and turn the switch to the “on” position.
- Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
- Repeat Steps 1 and 2 two more times.
Does a new airbag module need to be programmed?
When you buy a new control module,
most of the time it will need to be additionally programmed /coded to the car to inlcude the VIN and the configuration
. … The most common reasons why the airbag light is on besides the obvious—if the car was in an accident—are clockspring and under-seat wiring (70% of the time).
Do airbags need to be programmed?
If your airbags have deployed during an accident, your
airbags will need to be replaced
, and your airbag control module will need to be replaced or reprogrammed. … It is recommended that a licensed technician replace damaged or deployed airbags to ensure proper care for safety on the road.
How do you remove an airbag control module?
- First, find the SRS computer module. In most cars, it is under the center console that is between the two front seats, or center of the dash on the floor. …
- Disconnect the positive battery cable and wait 3 min.
- You are now safe to unplug the airbag control module harness wiring plugs.
Is it safe to drive with a airbag light on?
Is it safe to drive with an SRS light on? … It doesn’t necessarily mean that the car isn’t safe to drive but it’s like playing with fire if you do. When this light is on it means your
safety system isn’t working at 100%
and in some cases, it could mean that your airbags are disabled and will not deploy in an accident.
What does airbag module do?
Also known as the airbag sensor, diagnostic unit, and computer module, the airbag module is
responsible for receiving information from the collision sensor
. … Found in all vehicles, the airbag module is a computer that stores information. Thus, during a collision, the impact data is stored in the air bag module.
Can you swap airbag module?
Airbags are not repaired and not repacked
. The airbag control module however can be reset to clear crash history and then can be used again instead of purchasing a new airbag control module.
How much is an airbag control module?
The average cost for an airbag control module replacement comes
between $685 and $712
for most cars and locations. The labor costs for this procedure are estimated between $103 and $130, while the cost of the parts is more expensive at $582.
What is restraint control module?
A restraints control module (RCM) for
a vehicle is provided including a memory device
. The memory device stores a deployment time of a deployment event. … One of several advantages of the present invention is that it provides an apparatus for indicating when an RCM has been on a vehicle that has been in a collision.