Where is the computer module on a 2007 Ford Explorer Sport Trac? Thanks for the great question. The code is located on
the Smart Junction Box
which is located on the drivers side kick panel and up behind the dash a little. You will need a flashlight to see the 5 digit code.
Where is the computer module located on a 2005 Ford Explorer Sport Trac?
The sticker should still be on teh module, and according to the service manual, the module is located
behind the passenger side air bag
.
Where is the computer module on a 2004 Ford Explorer Sport Trac?
It is located
on the passenger side of the engine compartment
.
How do you reset the ECU on a Ford Explorer?
- Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
- Disconnect the negative battery terminal.
- Wrap the negative clamp in a towel.
- Leave the negative battery cable off for a minimum of five minutes.
Where is the computer module on a 2002 Ford Explorer Sport Trac?
It is
below the seat belt mechanism
. You have to pull out the top plastic panel off, then loosen the lower panel to be able to see the face of the computer module. The code is on a sticker on the face of the module.
How do I get the factory door code for my Ford Explorer?
If you have the owner’s manual to your vehicle handy, you can check it for the factory default code. This should be in
the owner’s wallet card
which is usually kept in the glove compartment. If the owner’s manual is lost, you can find the factory code on the label of the Remote Anti-Theft (RAP) module.
How do you reset the door code on a Ford Explorer Sport Trac?
From the vehicle list menu, select
Door Keypad
Code. Enter your factory key code that can be found in the owner’s manual. Enter your new personal key code. After you have entered in your factory code, wait for the prompt and enter in a new 5-digit key code of your choosing.
Can you reset a body control module?
Body Control Module also known as BCM is a special part in an automobile. If the central system is not working properly,
a professional will
perform a Body Control Module reset to make things perfect again.
How do you diagnose a bad PCM?
- Your “check engine” light is on.
- Other warning lights may be on, including traction control and ABS.
- You lose fuel economy for no apparent reason.
- Your car stutters when starting, requires multiple attempts, or won’t start at all.
- Stuttering or stalling during idling.
What are the signs of a bad ECM?
- Check Engine Light Starts Flashing. …
- Stalling or Misfiring Engine. …
- Engine Performance Issues. …
- Vehicle not starting. …
- Poor Fuel Efficiency.
How do I find my Ford factory code?
You can find the factory-set
five-digit Keyless Entry code on a wallet-sized card
(see image below) that was provided with the Owner’s Manual for your vehicle.
How do you use the keypad on a Ford Edge?
- Invisible Keypad.
- Raised-Button Keypad.
- To unlock the driver’s door, enter the factory-set five-digit code or your personal code. …
- To unlock all doors, enter the factory-set code or your personal code, then press 3•4 within five seconds.
How do I change the code on my Ford Explorer?
- On the keypad, enter the 5-digit, factory-set code that came with your vehicle. …
- Within five seconds, press the 1-2 button on the keypad.
- Enter your desired, new 5-digit code. …
- Press the 1-2 button on the keypad to save your new personal code.
How do you unlock a Ford Explorer without the key?
How do you unlock a Ford Explorer without the key? To open a ford explorer without keys
enter in the five-digit code in order on the keypad then press the 3-4 button within five seconds of entering your code
to unlock your doors.
How do you reset the keyless entry code on a Ford Explorer without factory?
- Obtain a factory code using an online generator.
- Press button numbers one and two. …
- Enter the new personal code that you have chosen to use moving forward.
- Press buttons one and two again. …
- The doors should lock themselves and unlock.
