The inertia switch is located
behind the trim on the left-hand side of the vehicle
, forward of the front door post, below the fascia.
How do you know if an inertia switch is tripped?
if it tripped,then
the button will pop up and all you need to do is push it back down until it clicks/stays down
. it’s rare for the inertia switch to fail,but possible.
Where is the fuel pump inertia switch located?
Look for the fuel pump switch or inertia switch. This is a small box with a plastic button on top and an electrical connector at the bottom. On some vehicle models, this will be located
in the luggage compartment
. Look on a side panel for a small, round button which you can pry off with a small screwdriver.
How do I reset my fuel shut off switch?
- Turn the ignition switch OFF.
- Ensure that there is no fuel leaking in the engine compartment, along any of the lines or at the tank. …
- If no leakage and/or odor is apparent, reset the switch by pushing the reset button on the top of the switch.
How do you turn off an inertia switch?
The inertia switch was reset by
simply pushing the red button on the switch
. The switch could also be manually pushed to turn off the fuel pump, which worked nice for turning off the fuel pump when servicing the fuel system.
What causes inertia switch trips?
The design of the fuel pump inertia switch causes it to turn off the fuel pump if a vehicle is involved in an accident. However, in certain incidents such as a
blown tire
or hitting a pothole in the road, the switch has the potential to trip. A sudden stop or change in direction activates the switch.
Can an inertia switch reset itself?
A good inertia switch should trip completely on a collision only(sudden stop or airbag deployment), so engine wouldn’t restart without a reset. And a good switch wouldn’t trip by being towed or hitting a bump,
nor reset itself
, so you could have a bad switch.
How do you reset the fuel pump sensor?
- Turn the ignition switch to the on position.
- Press the Odo / Trip button until the odometer is in ODO mode.
- Turn off the ignition.
- Press and hold the Odo / Trip button.
- Release the Odo / Trip button.
How do I know if my fuel pump fuse is bad?
- Engine stalls. One of the first symptoms of an issue with the fuel pump relay is an engine that suddenly stalls. …
- Engine does not start. Another symptom of a faulty fuel pump relay is an engine that does not start. …
- No noise from the fuel pump.
What are the signs of a faulty fuel pump?
- Sputtering Engine. Your fuel pump is telling you something if your engine starts to sputter once you’ve hit the top speed on the highway. …
- Overheating Engine. …
- Low Fuel Pressure. …
- Power Loss. …
- Surging Engine. …
- Gas Mileage Decrease. …
- Dead Engine.
What would make my fuel pump not work?
These include a bad fuel pump relay or control module, a
blown fuse
, a wiring fault, loose or corroded wiring connector at the pump, or even an issue with the anti-theft system. … These include a plugged fuel filter, pinched fuel line or a bad fuel-pressure regulator.
In the event of an accident, the “Fuel Reset Button”
will turn off the fuel pump and system.
How do you reset an inertia switch?
Press down the rubber reset button on the top
of the inertia switch. 3. Turn the ignition switch to position ‘II’, pause for a few seconds, then return the key to position ‘0’.
Should inertia switch be up or down?
The inertia switch is a safety item incorporated by Ford in the fuel system of its vehicles. The only time the inertia switch should trip is during a collision. … With the inertia switch in the open position, the
red button is raised up
. It is not supplying power to the fuel pump in this position.
How much is a inertia switch?
| Part No. Price | 1108 Condition: New $59.99 |
|---|
Is there a fuel shut off switch?
The fuel pump shut off switch is designed to disengage the power to the fuel pump when a vehicle comes to an instant stop. … The fuel cut-off switch is a safety reset switch which starts the fuel pump and allows gas flow to the engine.
