Depress the TPMS reset button located
below the steering wheel
until it blinks three times. Turn the ignition off and remove the key. Start the engine and let it run for 20 minutes while the system records the new pressure of each tire.
The TPMS reset button is usually located
beneath the steering wheel
. If you are unable to find it, refer to your vehicle’s owner’s manual. Inflate all tires to 3 PSI over their recommended amount, then deflate them completely. Be sure to include the spare tire, as it may have a sensor as well.
Shortly after, the “system error tpms” message should change to say “system ok”. To reset the tire pressure monitor or tpms system in your 2017 jeep wrangler vehicle, turn the ignition key to the “on” position and depress the tpms button,
usually located under the dash
, until the tpms light blinks several times.
How do you reset the tire pressure sensor on a Jeep?
- Drive your car at 50 mph for 10 minutes to reset the sensor.
- Find a place to park and turn off your car completely.
- Turn your key to the “On” position without turning the car back on.
- Press the TPMS reset button and hold until the light blinks three times.
- Release the button.
How do you turn off the tire pressure light on a 2011 Jeep Liberty?
To reset the tpms on the 2011 jeep liberty make sure the tire pressure is correct, then turn on the vehicle. Now hit the reset button that is to the right of the steering wheel and
wait ten minutes
. In some cases you may need to hold the button down till the light flashes.
Can I reset the TPMS by disconnecting the battery?
Find the battery and disconnect the negative battery cable. You will need a wrench to do this. Once the battery is disconnected, turn your vehicle on
and press the horn for approximately three seconds
. This will drain any remaining energy stored in the vehicle’s electrical system.
TPMS stands for Tire Pressure Monitoring System. In most vehicles the TPMS reset button is
found beneath the steering wheel
. After changing the tires on your vehicle, the TPMS needs to be electronically reset in order to clear the error code. … Start your vehicle and wait 20 minutes and the sensor will refresh.
To the right of the steering wheel
is a button that will be labeled tpms or something close. Hit this and hold it down until it begins to blink. Once it blinks leave the car sit for about 20 min, as it will take this long for it to recalibrate.
How do you clear a TPMS light?
Turn the car key to “on” but don’t start the vehicle. Press and hold the TPMS reset button until the tire pressure light blinks three times. Release the button and start the car. The light should go off
within 20 minutes
.
How do you reset the tire pressure sensor on a Jeep Liberty?
Locate the TPMS reset button under the steering wheel and press in, holding until the tire pressure light blinks three times. Start the
car and wait 20 minutes
for the sensor to refresh. Inflate all tires to 3 PSI over their recommended amount, then deflate them completely.
Why is my TPMS not working?
TPMS problems can include any of the following: …
The TPMS module itself is not functioning properly
or has failed because of a voltage supply, wiring or internal electronics fault. • The tires were serviced or rotated recently and the relearn procedure was not done correctly.
Why TPMS light on but tires are fine?
TPMS Light stays on all the time
This could either mean
air pressure in
one or more of your tires is low. If you have already checked and know that this isn’t the case, then it could indicate that the TPMS sensor is not reading correctly.
What should the tire pressure be on a 2011 Jeep Liberty?
Recommended tire pressure for 2011 Jeep Liberty is
33 psi for front tires
and 33 psi for rear tires.
What should the tire pressure be on a Jeep Liberty?
Proper tire pressure for the Jeep Liberty is
33 PSI for front and rear tires
. You will need to add air or release it from each tire, to get to the recommended setting.
How do you reset the tire pressure light on a 2009 Jeep Liberty?
Locate the TPMS reset button under the steering wheel and press in, holding until the tire pressure light blinks three times. Start the car
and wait 20 minutes
for the sensor to refresh. Inflate all tires to 3 PSI over their recommended amount, then deflate them completely.
