Always
keep your hands on the sides of the blade
while operating…. never in front of blade! 10. Maintain a well-balanced position and feed work into blade firmly, but without pushing too hard.
When cutting short pieces of wood they should be held?
Small pieces should be held in
a clamp or jig
. 3.
When cutting material What is the minimum distance the hands should be kept from the blade?
Keep your fingers away from the cut line and blade.
2 inches minimum
. 11. When cutting a tight curve, first cut relief cuts then push the work piece slowly without twisting or bending the blade.
When running the table saw what must you do before making any adjustments?
Make
sure that the blade has stopped turning
before you adjust the table saw. The reasons are obvious. Making adjustments can get hands too close to the blade, and even a slowly spinning blade has a multitude of sharp edges that can do damage.
Which machine do you use to cut across the grain of a piece of stock?
If you’re cutting across the wood grain,
a crosscut saw
is the best tool. Its teeth angle backward with a beveled edge while cutting on both the push and pull strokes for a clean and accurate notch.
When cutting small pieces of material you must secure it to the table of the saw using a?
9. When cutting small pieces of material, you must secure it to the table of the saw using
a clamp
.
What should you hold the workpiece securely against?
• Use
clamps
to support workpiece whenever possible.
workpiece by hand, you must always keep hand outside of “No Hand” area. Do not use this saw to cut pieces that are too small to be securely clamped. Your hand if placed inside the “No Hand” region can easily slip or be pulled into the blade.
What is the minimum distance you should maintain between your fingers and the band saw blade?
Keep hands and fingers at least
two inches
from the band saw blade. Never force a workpiece. If the workpiece does not feed smoothly, turn the band saw off and back the workpiece away from the jammed or uncompleted cut. Use a push stick when cutting small workpieces.
What is the minimum distance your finger need to be from any blade or moving part?
Keep your fingers at least
2 inches from
the side of the blade.
How far away from the blade should our hands be this is called the safety margin when cutting the blanks to length?
Hold or clamp the material securely before making any cut. 4. Keep hands
at least 4 inches away
from the rotating saw blade when making a cut.
How must the saw blade be held after the cut is finished and before the blade stops rotating *?
Q. How must the saw blade be held after the cut is finished and before the blade stops rotating?
Release it to the up position. Hold it in the down position
.
Which operation should be performed when using the table saw?
Use the left hand to hold the board against the fence and table. Use the
right hand to push the material through the saw
. When the stock is less than 6 inches in width, use a pushstick to push the trailing end through the saw. Never allow the hands to come closer than 12 inches to the saw blade.
What are the safety rules for a table saw?
- Wear Safety Equipment. …
- Keep the Area Clean. …
- Check Safety Features. …
- Always Disconnect Power Before Changing Blade. …
- Do Not Start the Saw With the Blade Engaged. …
- Maintain a Good Position. …
- Never Reach Over a Moving Blade.
How do you cut wood on the grain?
- Inspect the wood and determine which way the grain lines are pointing. All the lines in the wood will point in the same direction. …
- Place your saw, knife, wedge or axe into a position so it cuts along the same axis as the lines in the wood.
- Operate your cutting tool as normal.
What is cutting wood across the grain called?
A crosscut
is a straight, 90-degree cut that cuts across the grain of the wood. … On a table saw, you will usually use a miter gauge to make crosscuts. Crosscut. It’s the most basic cut you can make.
What is the number 1 safety rule of the band saw?
Safety Rules
Safety glasses are required. Never clear small pieces while blade is moving.
Never adjust saw or setup while saw is running
. Never cross arms.
What are safety precautions for a miter saw?
- Wear safety glasses or goggles, or a face shield (with safety glasses or goggles).
- If work is dusty, use a dust extraction system, and/or respirator or dust mask.
- Wear appropriate hearing protection.
- Wear protective footwear when required.
How far should you keep your fingers away from the cutting edges of hand and power tools?
Do not allow your fingers to come
closer than 50 mm
to the saw blade when cutting or crossing the path of the saw with your hands.
What are 5 major safety rules when working with the miter saw?
- Unplug the saw when you’re changing the blade or not using it.
- Keep your fingers at least 6 in. …
- Wear safety glasses and hearing protection when you’re operating the saw.
- Don’t reach under the blade while it’s spinning.
- Let the blade come to a complete stop at the end of each cut before lifting it.
What are the safety rules for bandsaw?
- Wear safety glasses or goggles, or a face shield (with safety glasses or goggles).
- Wear hearing protection that is suitable for the level and frequency of the noise you are exposed to in the woodworking area.
- Wear protective footwear when required.
How close can hands come to any tooling in the wood shop?
Stand to one side of the blade and never reach across, behind or beyond the blade while cutting. Again, your hands should never be IN LINE with the cutting blade. Maintain a four-inch margin of safety: do not let your
hands come closer than four inches from the blade
. USE the push stick.
What can you use a bandsaw for?
A band saw can be used
to cut curves
, even in thick lumber, such as in creating cabriole legs, to rip lumber and to crosscut short pieces. The most common use for the band saw, however, is in cutting irregular shapes. The second most common use is in resawing or ripping lumber into thinner slabs.
How high should the blade be adjusted above the wood being cut on the table saw?
the blade should be raised so its peak is
1/8′′ to 3/8′′ higher than your workpiece
. the blade should be raised so 1 full tooth is exposed above your workpiece.
When the blade is properly installed the teeth should point?
The teeth on the blade of a properly installed bandsaw should point
downward in the direction of blade travel
.
How do you maintain a table saw?
- Clean all sawdust that has accumulated inside the saw cabinet, adjustment controls, gears and motor. …
- Lubricate the gears and pivot points with a drying spray lubricant to keep the adjustment mechanisms operating smoothly.
- Clean cutting blades with pitch and gum remover.
What is the required guarding for a table saw?
In general,
blade guards
are required on table saws whenever ripping or cross-cutting is done. Some OEM guards on cheaper saws don’t work very well due to the fact that they are secured to the saw behind the blade with a thin metal blade called a splitter to help prevent kickback.
What is a useful tool for holding work during table saw operations?
Push sticks or push blocks
should be used when operating standard woodworking machinery, including table saws, band saws, radial arm saws, jointer/planers and shapers. These sticks protect the hand while allowing good hand control of the stock as it is pushed through the cutting head or blade.
When crosscutting short duplicate pieces on the table saw a safe method to use is?
When crosscutting short duplicate pieces on the table saw, a safe method to use is: A.
The fence alone as a guide
.
What does it mean to go with the grain of the wood?
doing something the wrong way.When you’re talking about. wood, you always want to go with the grain—
cutting or
.
planing a board in a way that follows the natural structure of
.
the tree
(Photo 1). The result is a smooth surface.
When cutting with the reciprocating saw why must the saw be held firmly?
Hold the saw firmly with both hands when making cuts. This saw will vibrate a lot during operation and must be held
tightly to keep the cut on line
and to avoid being dropped during operation. 4.
When using a stop to cut a workpiece to a set length?
When using a stop to cut a workpiece to a set length…
The piece between the stop and blade must be held in place by the operator
(Always hold the workpiece!) Stops are for wimps; never use them.
