Where should your workpiece be placed when using a disc sander?
ALWAYS hold the workpiece firmly on the table
when sanding on the disc.
On which side of the spinning disc sander should you sand your workpiece?
ALWAYS hold the workpiece firmly on the table when sanding on the disc. AVOID kickback by sanding in accordance with directional arrows.
Sand on downward side of disc
. Sanding on the upward side could cause the workpiece to fly up causing injury.
When using a disc sander should you hold the workpiece against the side of the rotating disc?
Always sand on the downward motion side of the disc
( Figure 17-3). The rotation helps to hold the workpiece against the table. If you sand on the upward motion side, the disc will lift the piece off the table and cause a kickback.
When using the belt disc sander floor model where should you hold the piece you are sanding?
Always sand on the downward side of the sanding disc
when using the disc sander. Sanding on the upward side of the disc can cause the workpiece to fly out of position, resulting in injury. 10.
When using the disc sander you should push your work against the?
Do not sand stock that puts your fingers within 2′′ of the abrasive. True. When using the disk sander, you should hold your work securely against the:
Downward motion side
.
What are the biggest sanding mistakes to avoid with a sanding machine?
Avoid pushing down with too much pressure on the sander
.
However, doing this can cause issues like swirls, cut-through, uneven sanding and other problems, such as excess heat and loading.
What is the main purpose of a disc sander?
Made up of a circular abrasive paper, mounted on a circular plate; the disc sander is ideal for
end grain work, shaping subtle round corners and removing large amounts of material quickly
. The work is supported by a flat table which sits in front of the abrasive disc.
When using a disk sander sand only on the side of the disk sander that is moving?
Always sand on the down travel side of the disc / belt
. The rest should be adjusted so that it is no more than 1/8” from the disc. Make adjustments only when the sander is at a complete stop. Keep fingers away from the abrasive surface on the sander.
Do you hold material loosely while sanding?
Dust mask advised. Don't wear loose clothing or gloves, keep long hair tied back.
Never adjust
Sander or setup while Sander is running. … Sanding end grain or curved pieces that go in and out of end grain is dangerous.
When using the disc sander do you sand on the upside or the downside?
Sand on the
downward side of a disc sander so that the wood is driven onto the table by the machine's rotation
. Enclose all drums, disk or belt sanding machines with an exhaust dust hood that covers all portions of the machine but the portion designed for the work feed.
Is an orbital sander the same as a palm sander?
As compared to a palm sander, orbital sanders are
more massive tools
, which means that palm sanders are smaller and more lightweight. The motions of orbitals are Circular and orbiting, and palm sanders only have orbiting motion. If you want to work with larger pieces, orbital sanders are better than palm sander.
When would you use a belt sander?
Belt sanders are multiuse tools. They are commonly used for trimming to a scribed line (photo),
sanding very rough surfaces
, leveling surfaces (like a replacement board in a hardwood floor) and freehand rounding and shaping.
Does floor sanding create a lot of dust?
Do expect dust
Yes, when you are sanding the
floors, dust is created
. That is just part of the process and there is no way around it. … We always put plastic around the areas not being done, and our machines are good at collecting a lot of the dust. We also vacuum the floors between each coat.
What PPE should you use when sanding?
- Wear appropriate personal protective equipment, including safety glasses, goggles or a faceshield, and footwear.
- Use hearing protection appropriate for the noise level you will be exposed to.
- Operate sanders with the local exhaust ventilation on.
What are common hazards when working with sanders?
All sanders should be ventilated carefully. The primary safety hazard of belt sanders is that
workers may catch their hands, clothing, or jewelry in the in-running rolls
. Also, contact with an abrasive surface can cause abrasions and lacerations.
