If you want to see live RIP advertisements, you can use
the debug IP RIP command
. You can see how in this example for router A the router is sending advertisements on both interfaces to a broadcast destination. It is also receiving updates coming from B on 10.1. 1.2 through the serial interface.
Which command will show all RIP networks being advertised by a router?
The show ip protocols command indicates that the proper networks are configured for RIP advertisements. You can confirm that these RIP advertisements are being received by looking at the routing table of R1 and R2 using the
show ip route command
.
Which of the following commands will enable RIPv2 on a router?
On router R1, in the global configuration mode, enter the
router rip command
to enable RIP. In the RIP configuration mode, change the version of the protocol to 2 by using the version 2 command. Next, use the network 10.0. 0.0 command to include the Fa0/1 interface on the router R1 in the routing process.
Which command configures RIPv2 on a router and advertises a network of 192.168 20.0 24?
Configuring RIPv2 begins with configuration of the router instance of RIP via the command router rip . RIPv2 is configured inside of the router instance with the command version 2 . Then the network of 192.168. 20.0/24 is advertised with the
command network 192.168
.
Which command would you use to confirm that RIPv2 is running?
You can use the debug ip rip , show ip protocols , and
show run commands
to confirm that RIPv2 is running. The show ip protocols command output for R1 is shown below.
What is command for RIP?
The
no shutdown (RIP)
command in router-RIP configuration mode will enable RIP. This command enables RIP on the switch. Issuing this command enables RIP, but to send and receive RIP route updates and to route packets via RIP you must also specify interfaces on which RIP will run by using the network (RIP) command.
How do I enable RIP?
- Step 1 Enable the RIP routing process, which places you in router configuration mode via the Router#router rip command.
- Step 2 Specify those networks that should be advertised using RIP via the Router(config-router)#network [network-number] command.
How do I enable RIPv2?
Cisco routers don't enable RIPv2 by default. To use RIPv2, you must
use the ver 2 command in RIP Router Configuration Mode
. RIP automatically summarizes routing updates. You can disable this by using the no auto-summary command.
How do you implement RIPv2?
- Enabling RIP routing protocol on the router.
- Specifying the RIP version to run.
- Configuring the network addresses to be included in routing updates or specifying the interfaces to participate in routing updates.
How do I check my router protocol?
show ip route –command
will give you the output of running protocol and routes on cisco routers, you can identify the which routing protocol is running on routers by its codes.
What is the difference between RIP version 1 and 2?
RIP v1 is an older, no longer much used routing protocol
. RIP v2 is a classless protocol and it supports classful, variable-length subnet masking (VLSM), CIDR, and route summarization. … RIPng works basically in the same manner as RIP v2 with one notable exception. RIPng can only run on IPv6 networks.
Why RIPv2 is not suitable for a larger global network?
RIPv2 is also a distance vector routing protocol but has a few enhancements to make it more efficient than RIPv1. Although RIPv2 is more efficient than RIPv1, it is not deemed suitable for larger, more complex networks. It simply
gives you more flexibility on smaller networks
.
How do I enable OSPF on my router?
- Use the command router ospf process ID to start OSPF.
- Use the network command to enable the interfaces.
- Identify area assignments.
- (Optional) Assign the router ID.
What makes a router a boundary router in RIP?
What makes a router a boundary router in RIP? …
If a router has multiple interfaces in more than one major classful network.
What parameters does RIP use?
However, it is easy to configure, because
RIP does not require any parameters
, unlike other protocols. RIP uses the User Datagram Protocol (UDP) as its transport protocol, and is assigned the reserved port number 520.
How do I show ip route?
To display the current state of the routing table,
use the show ip route command in user EXEC or privileged EXEC mode
. The show ip route command is a powerful tool to use at this point in your search. You can directly examine the routing table to determine if an entry for the host exists.
