If the belt mechanism is loose or slipped or the belt is damaged
, it may not be spinning with enough force. If the belt is broken or fully off the rollers, then it won’t spin at all. A washer that won’t spin isn’t washing. If it can’t agitate clothes, then clothes don’t get clean.
How do you fix a washer that won’t spin?
- Redistribute an off-balanced load of laundry. …
- Level an off-kilter washer. …
- Check the power source. …
- Stop using an extension cord. …
- Inspect the spin switch. …
- Stick to high efficiency detergent with a front-load washer. …
- Undo any kink in the hose. …
- Track down a blockage in the drainage system.
Why does my Frigidaire washer not spin?
Common solutions for: Frigidaire Washer won’t spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. …
If the lid switch assembly fails
, the washer will not spin.
How do you reset a Frigidaire washing machine?
- Verify that your Frigidaire front washer is plugged into a working electrical outlet and turned on; otherwise, you won’t be able to reset it.
- Press and hold the “Spin Speed” and “Soil Level” buttons together for a few seconds.
What would cause a front-load washer not to spin?
Front-load washer tubs spin thanks to a drive belt that runs off of the motor.
A loose, frayed, or torn belt
could be why your washer won’t spin. Overloading your washing machine can cause the belt to loosen or become worn out. Inspect the drive belt closely.
What causes a Maytag washer not to spin?
One of the most common reasons for a Maytag top load washer not spinning is
an incorrect wash cycle or spin setting
. GENTLE, HANDWASH, or DELICATE settings utilize slower spin speeds for more fragile fabrics. Some model washers also allow you to vary the spin speed, making it slower or more rapid, for different loads.
How do you reset the spin cycle on a Whirlpool washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When
you turn it back on
it should be reset.
What would cause a Whirlpool washer not to spin?
As a safety feature, Whirlpool washers will not spin
if the lid switch is not activated
; ensure the lid is properly closed and, if it is and the spin cycle is still not activated, you may need to replace the lid switch.
How do I find the error code on my Frigidaire washer?
- Wake the washer by pressing any button.
- Wait 5 seconds.
- Press and HOLD the Start/Pause and Cancel buttons simultaneously.
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer
and then plugging it back in often serves as the means to reset it
.
Why is my top loader not spinning?
The lid switch on a top load washing machine is used as a safety device to prevent the motor circuit from operating when the lid is open.
If the lid switch fails, the washer may not spin
. … If the switch is being activated but there is no power being supplied to the motor, then the switch may be defective.
Why are my clothes too wet after the spin cycle?
Overloading can lead to an imbalance that reduces the washer’s spin speed
, leaving clothes too wet after spin cycle completes. If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle.
How do I know if my washing machine belt is bad?
Signs The Belt In Your Washer Is Bad
When the belt in your washer begins to wear down, it may slip occasionally. This can create a squealing noise that gets louder as the belt breaks down over time. You might also
smell burning rubber
.
