When this light is on, that means
your airbags are deactivated
. It means they will not deploy properly if you get into an accident. If your car’s battery has drained recently, it may have also depleted the backup battery that powers the airbags.
How do I get my airbag light to turn off?
- Turn on the ignition switch with your car key. …
- Wait for the airbag warning light to turn off. …
- Turn the ignition switch of your car back off for a little longer than three seconds.
- Repeat steps 1 through 3 twice to make three times total.
How do you reset the airbag light on a seatbelt?
- Put the key into the ignition and turn the switch to the “on” position.
- Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
- Repeat Steps 1 and 2 two more times.
Why does my airbag warning light stay on?
The airbag light indicates
that something is wrong with the seatbelts or airbags
. This means that it’s probably not safe to drive with the airbag light on. If it stays illuminated in your vehicle, we recommend having it towed to the dealership rather than driving it yourself.
Can I drive my car if the airbag light is on?
If the airbag light is on, it means
that the airbag will not be able to deploy in the event of an accident
. This is a dangerous proposition, and it means that you should avoid driving if at all possible in that vehicle.
What does the airbag light look like?
The SRS warning light on the dashboard usually looks like a side view of a person sitting in a seat with a seat belt on, with
a large circle (the airbag) in front of the person
. It will normally light up briefly each time you start your vehicle, and then go off.
How much does it cost to fix airbag light?
Number 1 — Reset Airbag Light
This process can take several hours of time and usually costs a few hundred dollars, although depending upon the type of car it may be up
to about $600
.
Where is the seatbelt sensor located?
The seat belt sensor can usually be found in
a vehicle’s SRS airbag module
, sometimes referred to as the ECU, or engine control unit. The SRS airbag module or ECU is usually located beneath the driver’s or front passenger’s seat, but it can be found in a few different locations as well.
Will disconnecting battery reset airbag light?
Often, all it takes to get rid of that pesky warning light is to reset your airbag sensor. …
Remove the terminal clamp and leave it disconnected for 5-10 seconds
to allow the airbag sensor to reset. Then reconnect the battery terminal and turn the vehicle on. With a bit of luck, the light will stay off.
How do I know if my airbag sensor is bad?
Symptoms of a failing airbag sensor
You can easily tell if the sensor is functioning
if the airbag warning light on the dashboard is illuminating every time you start the vehicle
. But, if the airbag warning light stays illuminated after starting the vehicle, this is an indication of an airbag sensor problem.
Is airbag light an MOT failure 2020?
If your airbag light is on or
your SRS supplementary restraint system warning lamp is on it will fail its MOT
. It comes under section 7.1. … You can also try to reset the airbag or SRS light which may resolve the problem.
Can a blown fuse cause the airbag light to come on?
Blown fuses can definitely cause the airbag light to come on
. … When the airbag system is malfunctioning, a mechanic or auto parts store should be able to read the code that the system is putting out which will give them a clue as to what particular problem the airbag is having.
How do I check my airbag light code?
To read the codes,
count the number of times the light flashes, wait for the pause and count the flashes again
. For example, two flashes, a pause and four flashes mean that your airbag system’s problem is a code 24. Code 12 means your battery voltage is low, while 13 means the airbag circuit is shorted or grounded.
How much does it cost to fix a seat belt sensor?
A clock spring or crash sensor may run around
$75 to $125
, a seat belt with pretensioner may cost you around $200 to $300, and the computer itself could run upwards of $800 to $1000. Keep in mind, pricing will vary by location and your vehicle make and model.
Can I replace airbags yourself?
For those of you who want to replace airbag units on your own, you’ll be happy to hear
there are no restrictions on this kind of work
. You don’t need to go to any sort of authorized dealer or mechanic to fo this work, except when the work butts up against your car’s warranty.
