Why Is My John Deere Mower Not Moving?

by | Last updated on January 24, 2024

, , , ,


Clogged Fuel/Air Filters

A blocked fuel filter can keep gasoline from flowing to your 's engine in adequate supply, resulting in a lawn mower that isn't drivable. Damaged or clogged air filters also can prevent your lawn mower from going forward or in reverse simply because the engine will overheat quickly.

Why won't my mower move forward or backwards?


Clogged Fuel/Air Filters

A blocked fuel filter can keep gasoline from flowing to your mower's engine in adequate supply, resulting in a lawn mower that isn't drivable. Damaged or clogged air filters also can prevent your lawn mower from going forward or in reverse simply because the engine will overheat quickly.

What causes a lawn mower not to move?

If your riding lawn mower won't move, the problem could be

a broken ground drive belt

. If the riding mower is slow and sluggish, the ground drive belt could be so worn that it slips. Either way, follow the steps in this repair guide and video to replace the ground drive belt on your lawn tractor.

Why won't my hydrostatic mower won't move?

Common reasons why a hydrostatic mower won't move include:

having old hydraulic fluid in the lines

, having air in the lines, or a worn drive belt. Usually, the best way to fix these problems is to flush the hydraulic lines and refill them with new fluid. Also, you can change out the old belt for a replacement.

Why can't I push my riding lawn mower?

The most common reasons why a riding mower won't move in neutral are

a seized brake pad

or a faulty drive belt. In some cases, the wheels on your machine may also get stuck in place, meaning that they won't spin freely.

Why wont my Cub Cadet go forward or reverse?

To operate your axles, your mower connects belts from the hydraulic pumps to the engine and from the engine to the mower deck. When inspecting the belts, look for excessive cracks, tears or wear. These conditions can cause the belt to

slip off the pulleys

, which can stop your mower from going forward or reverse.

How do you troubleshoot a hydrostatic transmission?

Troubleshooting Hydrostatic Drives

If the system is overheating, check the oil level in the tank, inspect the heat exchanger, check the

inline pressure filters

, inspect the crossport relief valves, and check the pump and case drains for excessive bypassing.

Why is my lawn mower turning over but not starting?

The most common reason for why your riding mower will turn over but not start is

likely due to bad gas or a dirty carburetor

. You can usually fix the problem by removing and cleaning out the carburetor and making sure that your gas is fresh.

How do you know if your lawn mower belt is bad?

  1. The belt has s​​​ide wall damage. Mower belt edges should be smooth and even throughout the entire length of the belt. …
  2. The belt has a glazed or bu​rned sidewall. …
  3. The belt is​​ cracked.

Why is my riding mower so slow?

Because a lawn mower is powered by a combustion engine that is powered by liquid fuel,

clogging

is a major issue that slows down or even shuts down performance. In fact clogging can occur in many areas of the lawn mower, including the fuel line, the gas cap, the carburetor, the “needle and seat” and the air filter.

Do hydrostatic transmissions wear out?

Not performing routine maintenance. The hydro has relief valves, so you cant work it past its designed intent, but you certainly can damage them if you try, just like a gear transmission. You can stress it by being rough with it, but really, these

last every bit as long as gear transmissions

.

Can you adjust a hydrostatic transmission?

Hydrostatic transmissions feature control rod linkage from the speed control lever (or foot pedal on some models) to the hydrostatic transmission. … These control rods

are adjustable

. By rotating the threaded linkage connector ferrules, the length and the resulting range of movement at the regulator valve can be altered.

What causes a hydrostatic transmission to slip?

By far, the most common reason for hydrostatic transmission failure is

old hydraulic fluid

. John Deere states that “Operating outside of the recommended oil air temperature range may cause premature hydrostatic transmission failure.” Oil must be changed when its anti-foam additive decays.

Can you push a riding mower?


You can't push hydrostatic

without disengaging the transmission. Fluid is pumped to the wheels to turn them, so if the motor is off the pump is too and the wheels won't turn. If you push the mower when it's off, the fluid already at the wheels will flow back into the pump and damage it.

How do you release the parking brake on a lawn mower?

Move the shift lever to forward,

press the brake pedal to release

the parking brake, and press the drive pedal to increase your speed.

David Evans
Author
David Evans
David is a seasoned automotive enthusiast. He is a graduate of Mechanical Engineering and has a passion for all things related to cars and vehicles. With his extensive knowledge of cars and other vehicles, David is an authority in the industry.