If the
carburetor is clogged
, try cleaning it with carburetor cleaner. If cleaning the carburetor isn't effective, rebuild or replace the entire carburetor. The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the lawn mower for a long period of time.
How do you start a Poulan riding lawn mower?
What do you do when your lawn mower won't start?
- Use fresh gas. Old gasoline can cause starting difficulties. …
- Check the spark plug. …
- Use the choke. …
- Prime the mower. …
- Check the air filter. …
- Check the cables. …
- Check for water in the fuel tank.
- Clear the starter cord of blockages.
Why does my riding lawn mower clicks but wont start?
If your riding lawn mower engine clicks when you turn the key but won't turn over, there's a pretty good chance your mower could have a
bad starter solenoid
. Other problems, though not as frequent, include a bad starter motor, a wiring failure, a weak battery or a locked-up engine.
How do you start a flooded riding lawn mower?
- Pull off the spark plug wire and unscrew the spark plug with a spark plug wrench. …
- Crank the engine a few times while the plug is out to draw air through the carburetor and dry it out.
- Replace the plug, turn off the choke and crank the engine.
How do you know if the ignition switch is bad on a riding lawn mower?
To check your ignition switch, you can
use an ohmmeter to see if there is any connection between the “S” and “B” terminals
. If there isn't any, the ignition switch is your problem and you will need to replace it to get your mower running properly again.
Where is the fuse on a Poulan riding mower?
Fuse is located
under the dash, just below the amp meter
.
What type of oil does a Poulan Pro lawn mower take?
Poulan Pro uses Briggs and Stratton engines in its products. On its website, Briggs and Stratton recommends using a
high-quality detergent oil
based on the temperatures in your climate. Engine oil products labeled as “SAE 30” work in temperatures above 40 degrees Fahrenheit but are not meant for cold conditions.
Where is model number on Poulan Pro riding mower?
You can find the applicable model and serial numbers
on the serial number tag located on the back of your mower's deck
.
How do I know if my lawn mower spark plug is bad?
Checking Small Engine Spark Plugs
If you haven't turned on your engine recently, your mower won't start and/or you have to tug repeatedly on the rewind to start the engine
, a damaged spark plug may be the culprit. These problems may also cause excessive fuel consumption, deposits on the cylinder head and oil dilution.
How do you start a lawn mower when its cold?
- Disconnect the spark plug cap and unscrew the spark plug from the front of the lawn mower engine. …
- Brush the tip of the spark plug with the wire brush to remove any carbon and oil debris. …
- Unscrew the air filter cover on the side of the mower.
Where is spark plug in lawn mower?
Spark plugs are typically located
on the back or side of a lawn mower engine
. Look for a short wire that's about 1/4-in. -thick leading to the top of a short, cylindrical protrusion from the engine. If you're not sure where the spark plug is, consult your owner's manual.
How do I know if my starter is bad on my lawn mower?
A bad starter can manifest itself in
a cranking noise without engine turnover, a clicking when the ignition button is pressed, or a mower that simply does not respond to attempts to start
. An indication of a bad starter motor is the absence of other electrical problems that can be more easily tested.
How do I start my lawn mower with a bad starter solenoid?
When I try to start my mower it just clicks?
The clicking noise comes from a part called the starter solenoid
. The solenoid connects the battery to the starter motor when the solenoid is energized. The key switch and the safety switches in the starter circuit combine to energize the solenoid. If the solenoid is clicking, the circuit that triggers it is working.
How do you know if an engine is flooded?
- Gas odor: If you smell gas, this could mean the engine is flooded.
- Emissions color: See a darker smoke? The engine may need a look.
- Trouble starting the car: If you're unable to start the car, it might be because the engine has excess fuel.
What causes lawn mower engine to flood?
Most commonly a result of improper starting, “flooding” results from various causes, including
over-priming, closed choke, stuck valve, gummed carburetor, or immediately trying to restart an automatic choke engine
. The easiest way to tell if your engine is flooded with gas is to remove the spark plug.
How do I Unflood my lawn mower?
Sometimes, starting fluid can help start a flooded push mower; after you remove the air filter,
spray a one-second squirt into the air intake port and crank the engine with the choke off
. If the engine turns over, it will quickly burn off the excess fuel, which will produce a billow of white smoke for a short time.
What is wrong when you turn the key and nothing happens?
If nothing happens when you turn the ignition key to the “Start” position, it means that
the starter motor doesn't turn over the engine
. Most commonly this could be caused by a dead battery; read above How to check the battery.
How do I know if my riding lawn mower solenoid is bad?
Symptoms of a Bad Solenoid on a Riding Lawn Mower
A riding lawn mower solenoid may be bad
when you hear a click or hum when you turn the ignition key and your mower doesn't start
. Another indication your solenoid may be bad is when a wire gets hot and begins to smoke or melt.
Can you jump start a lawn mower?
How do I know if my lawn mower fuse is blown?
How do you tell if a fuse is blown?
What does a fuse look like when it is blown?
Look at the fuse wire. If there is
a visible gap in the wire or a dark or metallic smear inside the glass
then the fuse is blown and needs to be replaced.
Who makes Poulan Pro engines?
Meet the Parent and Engine Manufacturers
The
Husqvarna Group
is the parent company of Poulan and other “offspring” brands, such as McCulloch, Weed Eater and Jonsered. Husqvarna has been producing outdoor power products since about mid-20th century, but it came into existence as a weapons foundry in 1689.
What is sae30 oil?
The SAE 30 oil is
a single grade oil with a viscosity rating of 30
. It's called a single grade (or monograde) oil because it only has one viscosity grade. This is different from a multi grade oil, like 10W-30, which is rated for both SAE 10W and SAE 30.
What oil does a Briggs and Stratton engine take?
Use
Briggs & Stratton SAE 30W Oil above 40°F (4°C)
for all of our engines. Check oil level regularly. Air-cooled engines burn about an ounce of oil per cylinder, per hour. Fill to mark on dipstick.
