VEGETABLE OIL FOR LUBRICATING CHAIN SAWS. To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. …
Rapeseed-based
(usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant.
Can I use canola oil in my chain saw?
Use canola oil – Canola oil is currently the
most common environmentally compatible chain-and-bar lubricant
. … Manufacturers and some users claim that there is a potential for extended bar-and-chain life when using canola-based products because it lubricates and adheres to metal better than petroleum-based oils.
What oil do you use for chainsaws?
Petroleum-based bar oil
has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner's manual suggests alternatives.
Can you use olive oil in a chainsaw?
Use chain saws weekly at the farm and we use motor
oil
as chain lube often, no problems. Olive oil would just be more expensive. Olive oil tends to get a bit gummy when used as a lubricant, but if you clean it once in a while with a decent solvent it should be fine.
What happens if you put the wrong oil in a chainsaw?
Two-cycle oil is good for up to five years when sealed, and many manufacturers list the oil's shelf life on the container. … Here's what can happen if you use bad oil in a chainsaw:
Deterioration of engine parts, including the carburetor, gasket and fuel line
. Overheating, stalling or shutting down.
Can I use rapeseed oil in my chainsaw?
To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. … Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-
and-bar lubricant
.
What is special about chainsaw oil?
The reason a special type of chainsaw bar oil exists is that
chainsaw chains and bars need a lubricant with certain qualities to keep those parts running smoothly
. … If the bar oil is not sticky, it will fly off the chain and cause friction to build up against the bar.
What happens if you run a chainsaw without bar oil?
No bar oil equals increased friction and heat
. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
Can I use car oil in my chainsaw?
Chain saw bar and chain oil isn't rated by SAE like traditional automobile motor oil. … If your manufacturer's bar and chain oil is unavailable, you can use
SAE 30 weight motor oil
to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can I use gear oil as bar oil?
Gear lube is
about the same as SAE 40 engine oil
(they are rated on different scales), so that would make standard bar oil and gear lube pretty close. I have used it before when I had nothing else, it's a lot better than no oil or waste oil. I didn't notice any difference in the performance of the oil pump.
What is SAE30 oil?
SAE30 is a
straight 30 weight oil used on your lawn mower and other 4 cycle outdoor equipment
. … SAE30 weight oil is rated only at the full operating temp of the engine. This means it is much higher than 30 when cold. Sometimes so thick that it cannot flow if it is cold enough out. The W means winter.
What weight is bar oil for a chainsaw?
Once temperatures rise, switch back to your standard bar and chain oil, which may be anywhere
between 20 and 50 weight (30 weight is standard)
. Using winter oil during summer might leave a lot more oil on the ground because the thinner oil won't adhere as well to the bar and chain.
Can I use 10w30 for chainsaw bar oil?
Can I Use 10w30 for Chainsaw Bar Oil?
Yes
, though it is not ideal for use in the winter. A 10w30 oil is multi-weight, meaning it will perform well in cold and heat. Yet 10w30 weight motor oil will be very tacky and viscous once the chainsaw heats up and starts to run.
How can I tell if I put oil in my gas can?
How to tell if oil is in gas, try this.
Take 2 brown paper bags, pour straight gas on one and the other with mix or supposed to be mixed on the other
. The one with mix should leave a oil stain after the gas has evaporated and the straight gas should not leave a stain.
How much chain oil should a chainsaw use?
When to Oil
Gas chainsaws use
about one tank of bar and chain oil for every tank of fuel
, so fill the reservoir every time you fill the tank.
