How Do I Reset My Maytag Neptune?

1. Unplug the washer for 1 minute from the electrical outlet.
2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
3. The motor has now been reset and is ready for you to start a cycle.

How do I reset my Maytag Neptune washer?

1. Turn off and unplug the washer. Wait 30 seconds.
2. Reconnect it and press the “Power” button. This resets the unit.
3. Continue regular use of the washer.

Can you reset a Maytag Neptune dryer?

The Maytag dryer might display an error code if a problem has arisen with the dryer. ... To reset the dryer if an error code occurs, press “Power/Cancel” twice and then reselect a cycle and press “Start.”

How do I troubleshoot my Maytag Neptune washer?

1. Check the plug to be sure the washer is plugged in. Check the circuit breaker or fuse box.
2. Straighten any kinks in the washer's hoses. Check the floor drain for any blockages or clogs. ...
3. Close the door tightly, and push “Start/Stop.”
4. Call Maytag's customer service line if your washer still doesn't spin or drain.

Is there a reset button on Maytag washer?

To reset the washer, press and hold the button for 20 seconds . The lid lock light can flash if the washing machine settings are changed after the washer has already started the wash cycle.

What causes a Maytag washer not to spin?

One of the most common reasons for a Maytag top load washer not spinning is an incorrect wash cycle or spin setting . GENTLE, HANDWASH, or DELICATE settings utilize slower spin speeds for more fragile fabrics. Some model washers also allow you to vary the spin speed, making it slower or more rapid, for different loads.

Why does my Maytag washer not start?

Check to see if your Maytag washer has blown a fuse if the washer is on a fuse box. You might have to replace it or call an electrician if the problem continues. ... If the outlet is receiving power to turn the appliance on, but the Maytag washer still will not power on, it can be an issue with a defective power cord .

Why is my Maytag Neptune dryer not starting?

If your Maytag dryer won't start but has power, make sure that the door is fully closed . As a safety precaution, a dryer won't start if the door isn't completely shut and latched. Usually, you can hear an audible “click” when the door closes and the latch engages.

Do electric dryers have a reset button?

Often, dryers are equipped with a reset button on the control panel . If the motor won't run, let the dryer cool for about ten minutes. Then press this reset button.

How do you run a diagnostic test on a Maytag Neptune dryer?

Press and hold the “Signal” button and the “Temperature” button simultaneously for three seconds . Release the buttons when the display screen clears. The display screen will show a list of problem codes if any have not been cleared.

Does code on Maytag Neptune washer?

The simpler “ dS” indicates the door has opened during operation . Likewise, close the door completely if “FL” — or “failure to lock” — appears. On the flip side, the code “LO” means the door will not unlock. To remedy this, ensure the door is tightly shut, press “Power Off” and restart the washer.

What does Fl mean on a Maytag Neptune washer?

F8 E1 or LF or LO FL Error Code in the Display of my Maytag Washer. Error Code F8 E1, LF, or LO FL all indicate that no water is detected entering washer after 13 minutes . Depending on your model, you could see any one of these error codes. See your Owner's Manual for further assistance.

What does the code LR mean on a Maytag Neptune washer?

The LR code means “ locked rotor ” which is just a way of saying the control is not seeing the motor turning.

How do I reset my Maytag washer?

Unplug the top load washer for a minute from the electrical outlet. Lift and lower the lid six times in 12 seconds. 30 seconds is the time to start lifting and lowering the lid. The motor is ready for you to start a cycle now that it has been reset.

Does a washing machine have a reset button?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. ... Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

How do I reset my Maytag washer language?

1. Press and hold the “Spin” and “Soil” button simultaneously for 10 seconds. A count down will be displayed on the console. Once the countdown has completed the unit will have successfully reset.
2. Select the preferred language from the console.