Turn the valve to “Pilot .” Near the valve, you’ll see a small button labeled “Reset.” Press this button while applying your lit match or butane fireplace lighter to the pilot light valve. Hold the flame steady until the pilot ignites, then release the button.
How do you relight a pilot light?
- Find the pilot light assembly and its reset switch. The furnace’s pilot light is usually positioned at the bottom of the unit by a knob. ...
- Set the reset switch to off. Turn the knob to the “Off” setting. ...
- Wait a moment. ...
- Relight the pilot light. ...
- Observe the furnace.
What causes a pilot light to not light?
There are several possible reasons why your gas furnace pilot won’t light: an ongoing draft , a faulty thermocouple, an accumulation of dirt, or an inefficient supply.
When igniting a pilot light do you light the match first?
Turn the pilot control knob to the “pilot” position. Light a match and hold it directly beneath the tube in the pilot opening. Press and hold the pilot control knob down until the flame lights. Remove the match, but continue to hold the knob down for 30 seconds before releasing it.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished , causing a safety hazard, and requiring immediate repair.
What do you do if your pilot light won’t light?
When the water heater pilot light goes out, first try relighting it, following the directions on the water heater label. If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple .
How can you tell if your pilot light is out?
- Locate the front cover panel on your furnace. It should be a little door that’s easily visible. ...
- If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame.
- If you don’t see a flame, your pilot light is out.
- If there is a flame, check the color.
Can I manually light my gas oven?
If you don’t have the owner’s manual, open the oven door and look in the bottom of the oven for a small hole marked “Pilot Light” or something similar. ... If the oven is designed to be manually lit for each use, turn the temperature dial on slowly. The gas should ignite. Remove your hand and the match immediately.
What does pilot light look like?
A natural gas flame should be a bright blue color with a small amount of yellow at the very tip . A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.
What does the pilot light look like on an oven?
A pilot light is a small blue flame that ignites a gas appliance . Most modern gas appliances have electric starters or igniters. In some older natural gas appliances the pilot light can go out due to drafts, condensation or mechanical failures.
Can a pilot light relight itself?
Relighting a pilot light may be possible, depending on the type you have. By design, an automatic pilot light does not need to be lighted or relighted; it turns on and off by itself . ... If an automatic pilot or igniter is failing to light the burners on your appliance, it typically needs to be replaced.
Can you get carbon monoxide poisoning from a pilot light?
A pilot light should be a crisp blue colour. ... A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning. Symptoms of this condition include dizziness, headache, fatigue, nausea, unconsciousness, brain damage and death.
Are pilot lights always on?
The pilot light can be a “steady-on” pilot , or an ‘intermittent” or an electronic ignition system. The later type of pilot light is only on when the valve is open and the fireplace is operating. A millivolt valve utilizes a pilot light that is always lit.
How do you know if you have a bad thermocouple?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds , that’s the sign of a thermocouple malfunction.
How much does it cost to replace a thermocouple?
The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average .
How do you fix a yellow pilot light?
If you notice that you pilot light is burning yellow instead of blue, contact Jerry Kelly. The issue can typically be fixed by cleaning out the air intake valve to the pilot light , which should only be done by a professional who knows how to access and repair the part.
