To cancel the Delay Start or Delay Hours option: Press the Delay Start pad until the hours of delay indicator goes off . On most models, pressing and holding the Start or Start/Reset pad for 3 seconds will cancel any set cycle, including the Delay Start cycle.
How do I clear the error code on my GE dishwasher?
NOTE: Disconnecting power to the dishwasher for 30 seconds may clear the fault, error or function code. Unplug your dishwasher for 30 seconds to 5 minutes to try and reset the control board. This may clear the error and reset the dishwasher.
What does 2h mean on a GE dishwasher?
Found out that “2h” means a delay of 2 hours .
How do you clear a dishwasher error code?
The Fix: Pressing and holding the cancel button or turning off the power to the dishwasher for five minutes should clear the error code. If the error persists, you will need to troubleshoot the water heating system or call a professional to fix the issue.
What does 5h mean on GE dishwasher?
This means that you have a one hour delay start set on your GE dishwasher. You can start your GE dishwasher, wait 1 hour, and it will start the cycle after 1 hour. To cancel it out, press the START button until it cancels out the DELAY START. You can then use the dishwasher normally. Advertisement.
How do I run a diagnostic test on my GE dishwasher?
How do I put my GE dishwasher in diagnostic mode? While the dishwasher is in stand-by mode, press and hold down the pads – Cycle + Start – at the same time for about five seconds. The door status will be checked first (for 10 seconds) with other error checks following.
If the “Start/Reset” light is blinking, it indicates that the dishwasher has been reset . In case other lights are blinking, it might be due to an error. Try resetting your dishwasher by pressing the “Start/Reset” button and wait 2 minutes.
Why does my GE Profile dishwasher not start?
GE Dishwasher Not Starting Causes
The GE dishwasher will not start if the door is not closed properly or the control panel is locked. Power issues that may affect your dishwasher starting include blown fuses, a tripped breaker and disconnected power. The dishwasher also will not start if the water valve is turned off.
What do you do when your GE dishwasher won't start?
- Make sure the dishwasher is correctly plugged into a functioning electrical outlet.
- Confirm that the power switch is on. ...
- Check your home's circuit breaker or fuse box for tripped breakers or blown fuses.
Why would you delay dishwasher?
Available on many dishwasher models, the Delay Start option delays the start of the wash cycle. ... The benefit of the Delay Start option is that it allows you to run your dishwasher when its hot water demands will not conflict with those of the family . It also lets you take advantage of off peak utility rates.
How do you reset a GE dishwasher?
Press the “Start/Reset” pad on a front-control GE dishwasher to cancel the dishwashing cycle. The “Start/Reset” light will flash as the water pumps out, a process that takes about two minutes. When the light stops flashing, the dishwasher is reset and it can be restarted later.
Can you reset your dishwasher? Yes , you can reset your dishwasher by pressing the Start/Reset button on the appliance and waiting a few minutes. If your dishwasher still doesn't start, you may need to reboot the entire system by turning off power to the appliance at the house circuit breaker or fuse box.
How do I reset my dishwasher control panel?
How Do I Reset My Dishwasher Control Panel? Simply unplug your dishwasher. Wait for one minute, then plug it back in again , to reset the dishwasher control panel.
Why is my GE dishwasher flashing 888?
According to the owner's manual, “reset” is used to change a cycle during washing . The “reset” button will sometimes refuse to respond, displaying 888 on the panel and necessitating a couple of quick tricks to ease it back into action.
How do I know if my GE dishwasher control board is bad?
- Unplug dishwasher or disconnect power.
- Open the dishwasher door.
- Open console and disconnect the keypad ribbon connection from the control (at P1).
- Put console back together.
- Plug in dishwasher or reconnect power.
- Wait 5 seconds.
