Does this pose any risk to your chainsaw? In all honesty,
no! The additional moisture found on wet wood will not make any difference to the cutting process
. It doesn't place any additional resistance on the chainsaw, and no additional effort is required to cut through it.
Is it harder to chainsaw wet wood?
No, it is not bad to cut the wet wood
with your chainsaw. Dewdrops, raindrops, or the snow on the wood will not cause any harm to your chainsaw. It is, in fact, much easier to cut through the wet wood than dry wood because the extra moisture on the wood will act as a natural lubricant.
Can you run a chainsaw in water?
No,
you can not run a chainsaw in the water
. … The only way you can run a chainsaw underwater is by using specially designed chainsaws called hydraulic chainsaws or a pneumatic chainsaw. While a regular chainsaw cannot be submerged underwater, you may still be able to cut objects underwater using a gas-powered chainsaw.
Will rain hurt a chainsaw?
You can use a gas chainsaw in the rain, and even if it's pouring,
it's not going to damage your chainsaw
. As long as you don't submerge the engine underwater, you'll be fine.
What should you not do with a chainsaw?
One of the most important things you should not do with a chainsaw is cut in the kickback zone, which is essentially the top half of the end tip of the blade. Also,
never cut above your shoulder height
, and definitely never operate a chainsaw under the influence of drugs or alcohol.
Why does my chainsaw dull so fast?
If your chain dulls quickly, then it could be a couple of things. Check your user's manual to ensure that you are using the right sized file for your chain. Alternatively, you could
be applying too much pressure when you file
. This will create cutting edges that are too thin and dull quickly.
Can you use a chainsaw to cut firewood?
For most people, an
18-inch chainsaw
is an ideal length for splitting firewood. For indoor fireplaces, you want a 16-inch pice of firewood when all is said and done. However, if you're starting with massive tree trunks, then you may want a 20 or 24-inch chainsaw to get through the thickness of that wood.
Can you cut 2×4 with a chainsaw?
Chainsaws offer brute cutting power, but they aren't the most accurate tool in the shop. Nevertheless, you
can make a level cut with
your chainsaw using this simple technique. … You can build a basic square jig using 2 x 4s and a level, and then slide it over the log or pole you want to cut.
How long should logs dry before sawing?
You should seal the ends within minutes after being cut down; you should not wait hours, and definitely not days! The drying time will vary depending on the wood species and thickness of the logs, but they will take
at least one to two years
to dry – the longer you can leave them before you start building the better.
How many times can a chainsaw chain be sharpened?
To keep your saw cutting in a straight line, be a fanatic about filing each cutter with the same number of strokes and the same amount of pressure. Cutters can be sharpened up to
10 times or more
before the chain needs replacing.
Why does my chainsaw bar smoke?
This most commonly is a result of
a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut
. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Can you cut with the tip of a chainsaw?
This is generally the safest way to cut.
The most dangerous is to use the tip
, which can see the chain's rotation sending the business end of the saw upwards and directly at your mug.
How long should you let a chainsaw warm up?
ArboristSite Member
About 30 seconds with a few revs
.
Should you run a chainsaw at full throttle?
Chainsaws come with a chain break to prevent any injury that may occur from a kickback. To prevent a kickback while working, you should:
Apply full throttle before cutting
.
Avoid using the top of the chainsaw
.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw
once after you have gone through three chains on the same bar
.
