Typically, the most commonly used types are
10mm sockets and 36mm sockets
.
What is the size chart for sockets?
3/8′′ Drive 1/4′′ Drive 1/2′′ Drive | 6mm 4.5mm 9mm | 7mm 5mm 10mm | 8mm 5.5mm 11mm | 9mm 6mm 12mm |
---|
How do you measure socket size?
- Turn on the digital caliper and set it to read in inches, not millimeters. …
- Close the caliper jaws until each jaw rests on one flat side of the nut on opposite sides.
- Check the caliper display. …
- Turn on the digital caliper and set it to read in millimeters, not inches.
What are the 4 socket drive sizes?
These drive fittings come in four common sizes:
1⁄4 inch, 3⁄8 inch, 1⁄2 inch, and 3⁄4 inch
(referred to as “drives”, as in ” 3⁄8 drive”).
What’s the next size smaller than 1/2 inch?
Bolt Diameter Metric Standard | 5/16′′ 13mm 1/2′′ | 3/8′′ 14mm 9/16′′ | 7/16′′ 16mm 5/8′′ | 1/2′′ 19mm 3/4′′ |
---|
What is equivalent to a 15 mm socket?
SAE Metric Inch | 9/16′′ 0.563 | 15mm 0.591 | 19/32′′ 0.594 | 5/8′′ 0.625 |
---|
What are the standard wrench sizes?
Wrenches: Standard Combination Wrenches (
1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1
) Metric Combination Wrenches (6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19) Standard Flare Nut Wrenches (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 7/8) Note: Each wrench may combine two sizes.
Are 6 or 12-point sockets better?
Answer: It’s true that
12-point sockets are fine for most lightweight repairs
, but heavy wrenching calls for a six-point socket. A six-point socket is much less likely to slip off a stubborn fastener or round over the corners. Here’s why: (1) Six-point sockets have thicker walls, so they’re less likely to flew.
What are the most common wrench sizes?
Most common are the
1/4-inch, 3/8-inch and 1⁄2-inch ratchet
drivers, but 3⁄4-inch and 1-inch sets are available for heavy-duty work.
What is a 72 tooth ratchet?
Low-tooth ratchets generally range from about 20 teeth to as high as 40 teeth. That means you’ll see about an 18-degree swing arc to a 9-degree arc from coarse or low-tooth-count ratchets. … Fine, or high
-tooth-count
, ratchets range from about 72 teeth to 160 teeth.
Is 5mm the same as 1/4 inch?
5mm = just over 3/16 inch
.
6mm = almost
1/4 inch. 7mm = almost 9/32 inch (= a bit over 1/4 inch) … 11mm = almost 7/16 inch.
Is a 3/8 socket the same as a 10mm?
So what is a
10mm
socket equivalent? The equivalent imperial size of a 10mm socket is a 3/8 socket. Imperial sizes are known as SAE (Society of Automotive Engineers) or Standard.
How many inches is equal to 7 mm?
MM Approximate Size In Inches Exact Size In Inches | 5mm 3/16 Inch 0.19685 Inches | 6mm Just short of 1/4 Inch 0.23622 Inches | 7mm Little over 1/4 Inch 0.27559 Inches | 8mm 5/16 Inch 0.31496 Inches |
---|
What’s equivalent to a 30 mm socket?
Inches Millimeters Spanner | 1.063 27mm 1 1/16 AF; 27mm | 1.100 5/16 Wworth; 11/16 BSF | 1.125 1 1/8 AF | 1.181 30mm 30mm |
---|
How many mm means 1 inch?
How many millimeters in an inch? 1 inch is equal to
25.4 millimeters
, which is the conversion factor from inches to millimeters.