Why Does My Jeep Heater Blowing Cold Air?

by | Last updated on January 24, 2024

, , , ,

A car heating system blowing cold air can be due to a

faulty thermostat

, low coolant fluid level, malfunctioning core, a leaking cooling system, or problems with heating controls and blend door.

Why did my heat randomly stop working in my car?

A heater can stop working for a number of reasons, including: A

low antifreeze/water level in the radiator due to a leak in the cooling system

. A bad thermostat that isn't allowing the engine to properly warm up. A blower fan that isn't working properly.

Why did my heat stop working in my Jeep?

While there are a variety of reasons your Jeep Wrangler heater is not working, the most common 3 are a

broken heater blower motor

, a problem with the thermostat, or a failed heater blower motor resistor.

How much does it cost to fix a heater on a Jeep?

Jeep Wrangler Heater Core Replacement Cost Estimate. Labor costs are estimated

between $592 and $747

while parts are priced between $185 and $207.

What to check if heat is not working?

Check your power source—a tripped circuit breaker or blown fuse could be the reason for your failure. Reset your breaker or replace the fuse to see if that restores heat.

Check your filter

—if it's so dirty that your system is struggling to move air through it, your furnace could overheat and shut down.

What are signs of a bad thermostat?

  • The temperature gauge reads high and the engine overheats.
  • The temperature changes erratically.
  • The vehicle's coolant leaks around the thermostat or under the vehicle.

What do I do if my heater is blowing cold air?

When your furnace blows cold air,

try turning the heating unit off and on

. If the air feels warm for a moment or two, then switches to cold, it may be that the flame sensor is dirty. With a dirty flame sensor, your gas burner won't stay lit, causing the air to go cold soon after the furnace turns on.

Why is cold air blowing when the heat is on?

Your furnace may be blowing cold air

because the filter is too dirty

. A dirty air filter blocks airflow over the furnace's heat exchanger, causing it to overheat. When overheating, your furnace can trip a high limit switch, causing the furnace burners to shut off so that the heat exchanger does not crack.

How do I know if my heater control valve is bad?

  1. No heat comes out.
  2. Heat is always on and you can't turn it down.
  3. Heater operates erratically, putting out more or less heat without any control changes.
  4. Coolant leaks.
  5. Low coolant level.
  6. Higher-than-normal temperature gauge readings (from loss of coolant)

How long does it take to replace a heater core in a Jeep Wrangler?

Took

about 6 hours

, it's more tedious than hard.

How much does it cost to fix a heater core?

Replacing the heater core can be an expensive job, and usually costs

between $564 – $927

for parts and labor. The parts aren't particularly expensive, normally costing $80 – $234, but the location of the heater core means that labor costs tend to be quite high.

Can a heater core be repaired?

Unfortunately, there are

occasions

when a heater core can go wrong, and you may need to take it in to a mechanic to get it looked at and repaired. A heater core is not a very cheap part of your vehicle to get repaired and will often cost between $500 and $1,000 to repair if the entire heater core needs to be fixed.

Why isnt my heat working in my house?

If your furnace does not heat at all.

Thermostat malfunctions cause most heating system failures

. Other causes include a tripped circuit breaker or blown fuse, or—in the case of combustion furnaces—a pilot light that has gone out.

Why does my heater not kick on?

If your furnace is not kicking on,

it can be an issue with the thermostat

. You should first make sure that the thermostat is switched to the heating function. … You may also have an internal problem with your thermostat, which needs to be repaired by a professional.

Is heat not working an emergency?


A malfunctioning heater isn't considered an emergency unless it stops working during the winter

. If your heating system won't operate on a cold winter day, please call our emergency maintenance number as soon as possible.

How do I check if my thermostat is working?

Check the screen:

Check the screen of the thermostat and make sure that it is lighted

. A blank or unlighted screen could indicate a thermostat failure. Check the batteries: Many modern thermostats rely on battery power to operate. If the screen is blank or unlighted, a battery change could solve the problem.

Jasmine Sibley
Author
Jasmine Sibley
Jasmine is a DIY enthusiast with a passion for crafting and design. She has written several blog posts on crafting and has been featured in various DIY websites. Jasmine's expertise in sewing, knitting, and woodworking will help you create beautiful and unique projects.